Yaskawa CM048 User Manual download pdf

Yaskawa Electric America, Inc. – www.yaskawa.com

IG.AFD.20, Page 1 of 5

Date: 03/02/2012, Rev: 12-03

LONWORKS

Option Card

CM048



Unpack the

ORKS

Option Kit

and verify that all components are

present and undamaged.

Part Qty.

LonWorks Option Card

(UTC000057)

Installation Guide (IG.AFD.20) 1



Verify that the drive is one of the following series: E7, P7, F7, or G7.

The

LonWorks Option Card

is only compatible with these drive series.



Apply power to the drive or panel and verify that they function correctly.

This includes running the drive through the drive keypad (or the door

mounted Bypass controls, in case of E7B, E7L, or P7B. Refer to the

appropriate technical manual for information on connections and

operation.



Remove power and wait for the drive charge lamp to be completely

extinguished. Measure and verify the drive’s DC BUS voltage to be at a

safe level.



Remove the operator keypad and drive cover(s).

 Remove the operator keypad by depressing the tab on the right

side of the keypad and then pulling it out. In E7B, E7C, E7L, P7B,

P7C, or F7C, the keypad may already have been removed and

mounted on the enclosure door.

 Remove the drive’s front cover until the entire control card is

exposed. The number of covers and the removal procedure varies

by drive series and capacity. Consult the drive’s technical manual

for details. In E7B, E7C, E7L, P7B, P7C, or F7C, the keypad may

already have been removed and mounted on the enclosure door.

 Remove the option card hold-down plug on the left side of the

drive case by carefully compressing the top and bottom until it

becomes free of its holder and then pulling it out.



Mount the

ORKS

Option Card

on the drive.

 Align the 2CN connector on the back of the

LonWorks Option Card

with its mating 2CN connector on the front of the drive’s control board. Align

the two standoffs on the front of the drive’s control board with the two holes on the right side of the

ORKS

Option Card.

 Press the

LonWorks Option Card

firmly onto the drive’s 2CN connector and standoffs until the 2CN connector is fully seated and the drive standoffs

have locked into their appropriate holes.

 Standard Connection - Route the four wires from the

LonWorks Option Card

along the left side of the control board and connect them directly to the

R+, R-, S+ and S- terminals on the I/O terminal assembly as shown below.

 E7L Connection - Route the four wires from the

LonWorks Option Card

to terminal board TB4 on the E7L control card. The E7L control board is

typically mounted on the left inside wall of the E7L enclosure. Connect the wires as shown below.

 A noise free ground is essential for continuous, stable communications. DO NOT USE THE GROUND TERMINALS LOCATED ON THE DRIVE’S

TERMINAL BOARD OR CHASSIS. If an external, noise free ground is available, connect a ground wire from the ground terminal on the

LonWorks

option Card

to the ground. If no noise free ground is available, leave the ground terminal on the

LonWorks Option Card

un-terminated.

 Standard Termination - Set the Termination Switch S1-1 to ON as shown below. This is independent of whether the drive is the first or last device on

the

LonWorks

network.

 E7L Termination - Set the Termination Switch S1 to ON. This is independent of whether the drive is the first or last device on the

LonWorks

network.

PWR

RECEIVE

TRANSMIT

FAULT

LEDs

net

shield

SERVICE

Button

SERVICE

LED

RJ45

Ground

Terminal

1 2 3 4 5

Summary of Contents

Page 1 - Option Card

Yaskawa Electric America, Inc. – www.yaskawa.com IG.AFD.20, Page 1 of 5 Date: 03/02/2012, Rev: 12-03 LONWORKS® Option CardCM048 Unpack the LONWORKS

Page 2 - Date: 03/02/2012, Rev: 12-03

Yaskawa Electric America, Inc. – www.yaskawa.com IG.AFD.20, Page 2 of 5 Date: 03/02/2012, Rev: 12-03 R- (Yellow)S- (Blue)R+ (Purple)S+ (Orange)

Page 3 - IG.AFD.20, Page 3 of 5

Yaskawa Electric America, Inc. – www.yaskawa.com IG.AFD.20, Page 3 of 5 Date: 03/02/2012, Rev: 12-03  Setting the drive parameters  Remove power f

Page 4

Yaskawa Electric America, Inc. – www.yaskawa.com IG.AFD.20, Page 4 of 5 Date: 03/02/2012, Rev: 12-03  Connect to the LonWorks network.  Connect th

Page 5

Yaskawa Electric America, Inc. – www.yaskawa.com IG.AFD.20, Page 5 of 5 Date: 03/02/2012, Rev: 12-03 LONWORKS ® Option CardCM048Copies of this Insta

Comments to this Manuals

No comments

Yaskawa CM048 User Manual

Browse online or download User Manual for Equipment Yaskawa CM048. Yaskawa CM048 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Equipment Yaskawa CM048