Yaskawa CM093 User Manual
Browse online or download User Manual for Equipment Yaskawa CM093. Yaskawa CM093 User Manual
- Page / 11
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
V7 EtherNet/IP Option Kit
CM093
Yaskawa Electric America, Inc. – www.yaskawa.com
IG.V7.26, Page 1 of 11
Date: 05/24/2010 Rev: 10-05
1. Applicable products: Standard V7 drives CIMR-V7AM*) with Ethernet
specific software installed (not V74X or V7N). Check V7 monitor U-10 or
the PRG # on the V7 nameplate for version 8340 or 8350 software.
Note: To order a V7 with Ethernet software, use the following part number
format: CIMR-V7AM****1-057.
2. When using this Kit, it is strongly recommended that no connections be
made to the V7 drive's DC Bus terminals (+1 and -) on models CIMR-
V7AMxxxx1, where xxxx is 25P5, 27P5, 45P5, or 47P5. A connection for
a DC reactor (+1 to +2) or braking resistor (B1 to B2) is allowed.
3. Unpack the V7 EtherNet/IP Option Kit and verify that all components
are present and undamaged.
4. Connect power to the V7 and verify that it functions correctly. This
includes running the V7 from the operator keypad. Refer to the V7 Technical
Manual, TM.V7.01, for information on connecting and operating the V7
drive.
5. Remove power from the V7 and wait for the charge lamp to be
completely extinguished. Wait at least five additional minutes for the V7 to
be completely discharged. Measure the DC bus voltage and verify that it is at
a safe level.
6. Remove the operator keypad and V7 drive cover.
a. Remove the terminal cover by removing the retaining screw and lifting
out the cover.
b. Remove the operator keypad.
7. Remove the CN2 cover from the V7 terminal housing. Carefully snip the
3 tabs connecting the CN2 cover on the V7 housing and remove the cover.
8. Attach the Mounting Bracket. Align the mounting bracket as shown in the
figure to the right. Secure the mounting bracket to the V7 drive’s housing
using the M3 x 8 screw.
9. Wire the V7 drive I/O terminals prior to mounting the V7 EtherNet/IP
Option Kit as the option will obscure the power and control terminals when
mounted.
10. Mount the V7 EtherNet/IP Option Kit on the V7 drive.
a. Do NOT connect a ground wire to the screw on the back of the option kit.
b. Align the CN1 connector on the back of the option with its mating CN2
connector on the front of the V7 drive.
c. Simultaneously align connector CN3 (male RJ-45) on the back of the
option with connector CN1 (female RJ-45) on the front of the V7 drive.
d. Align the tabs on the option with their corresponding slots on the front of
the V7 drive.
e. Press the option and the V7 drive together until the tabs lock into their
associated slots.
f. Secure the option to the V7 drive by tightening the locking screw at the
top-center of the option.
g. Reinstall the operator keypad and all V7 covers.
CM093 EtherNet/IP Option Kit Parts Qty.
V7 EtherNet/IP Option Kit CM093 1
Option Mounting Bracket 1
Mounting Bracket Screw (M3 x 8) 1
Ferrite (Power and Motor Leads) 2
Ferrite (Ethernet Cable) 1
Cable Ties 3
Installation Guide (IG.V7.26) 1
WARNING
Dangerous voltages in excess of 400VDC (230V drives) or 800VDC
(460V drives) are present at the DC bus terminals of the drive.
Summary of Contents
Page 1 - V7 EtherNet/IP Option Kit
V7 EtherNet/IP Option KitCM093Yaskawa Electric America, Inc. – www.yaskawa.comIG.V7.26, Page 1 of 11Date: 05/24/2010 Rev: 10-05 1. Applicable products
Page 2
V7 EtherNet/IP Option KitCM093Yaskawa Electric America, Inc. – www.yaskawa.comIG.V7.26, Page 10 of 11Date: 05/24/2010 Rev: 10-05Data subject to chang
Page 3
Yaskawa Electric America, Inc. – www.yaskawa.comIG.V7.26, Page 11 of 11Date: 05/24/2010 Rev: 10-05V7 EtherNet/IP Option KitCM093Copies of this Install
Page 4
Yaskawa Electric America, Inc. – www.yaskawa.comIG.V7.26, Page 2 of 11Date: 05/24/2010 Rev: 10-05V7 EtherNet/IP Option KitCM09311. Diagnostic LED powe
Page 5
Yaskawa Electric America, Inc. – www.yaskawa.comIG.V7.26, Page 3 of 11Date: 05/24/2010 Rev: 10-05V7 EtherNet/IP Option KitCM093The V7 EtherNet/IP Opti
Page 6
Yaskawa Electric America, Inc. – www.yaskawa.comIG.V7.26, Page 4 of 11Date: 05/24/2010 Rev: 10-05V7 EtherNet/IP Option KitCM09317. Configuring the Eth
Page 7
Yaskawa Electric America, Inc. – www.yaskawa.comIG.V7.26, Page 5 of 11Date: 05/24/2010 Rev: 10-05V7 EtherNet/IP Option KitCM09318. Remove power from t
Page 8
Yaskawa Electric America, Inc. – www.yaskawa.comIG.V7.26, Page 6 of 11Date: 05/24/2010 Rev: 10-05V7 EtherNet/IP Option KitCM09323. Notes: a. It is str
Page 9
Yaskawa Electric America, Inc. – www.yaskawa.comIG.V7.26, Page 7 of 11Date: 05/24/2010 Rev: 10-05V7 EtherNet/IP Option KitCM093V7 EtherNet/IP Option K
Page 10
Yaskawa Electric America, Inc. – www.yaskawa.comIG.V7.26, Page 8 of 11Date: 05/24/2010 Rev: 10-05V7 EtherNet/IP Option KitCM093♦ Yaskawa Extended Spee
Page 11
Yaskawa Electric America, Inc. – www.yaskawa.comIG.V7.26, Page 9 of 11Date: 05/24/2010 Rev: 10-05V7 EtherNet/IP Option KitCM093♦ Yaskawa Standard Spee
Related products and manuals for Equipment Yaskawa CM093
Equipment Yaskawa AI-030 User Manual
(3 pages)
(3 pages)
Equipment Yaskawa V74X Drives User Manual
(62 pages)
(62 pages)
Equipment Yaskawa GPD315 User Manual
(5 pages)
(5 pages)
Equipment Yaskawa AI-020 User Manual
(2 pages)
(2 pages)
Equipment Yaskawa CACR-SRxxBF User Manual
(57 pages)
(57 pages)
Equipment Yaskawa CDBR-xxxB User Manual
(18 pages)
(18 pages)
Equipment Yaskawa GPD515/G5 User Manual
(76 pages)
(76 pages)
Equipment Yaskawa F7 to A1000 User Manual
(68 pages)
(68 pages)
Equipment Yaskawa J7 to J1000 User Manual
(19 pages)
(19 pages)
Equipment Yaskawa P7 to P1000 User Manual
(56 pages)
(56 pages)
© 2020, manymanuals.com. All rights reserved. | 0.497 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals