Yaskawa DS383 User Manual download pdf

DWG. NO. 02Y00025-0350

SHEET NO. 1 OF 6

REL. 05/05/93 (m-df )

For GPD 515, GPD 503, or GPD 575

Adjustable Frequency Drives

or VCD 703

Vector Control Drives

CHANGE RECORD

1 STD-5688 1-24-94

2 STD-6602 6-13-96

DIGITAL OUTPUT CARD (DO-08)

MODEL DS383

Before installing this option, a TECHNICALLY QUALIFIED INDIVIDUAL, who is familiar with this type of

equipment and hazards involved, should READ this ENTIRE INSTRUCTION SHEET.

IMPORTANT

This option may have been installed by the factory. However, certain steps can

only be completed at the installation site. Therefore, review and then perform

those steps which complete the installation process.

INTRODUCTION

When installed, this option allows the user to employ isolated type digital signals to monitor status outputs of the

drive (alarm signal, zero-speed detection, etc.).

This option card can be used on a GPD 515 drive, a GPD 503 drive, a GPD 575 drive, or a VCD 703 drive.

CAUTION

The option card uses CMOS IC chips. If proper electrostatic discharge

(ESD) protective procedure is not used when handling the card, the ICs

may be damaged, resulting in erratic performance of the drive.

INSTALLATION

1. Disconnect all electrical power to drive.

2. Remove drive front cover. Check that the CHARGE indicator lamp inside the drive is off.

3. Verify voltage has been disconnected by using a voltmeter to check for voltage at incoming power terminals

(L1, L2, L3).

WARNING

HAZARDOUS VOLTAGE CAN CAUSE SEVERE INJURY OR

DEATH. LOCK ALL POWER SOURCES FEEDING DRIVE IN

"OFF" POSITION.

NOTE: If this option is being installed on a GPD 515 with speed feedback, the speed feedback card needs to

be temporarily un-installed to allow access to the connector 2CN on the drive’s Control Board and terminals

TD1 through TD11 on the option card.

1 2 3 4 5 6

Summary of Contents

Page 1 - DIGITAL OUTPUT CARD (DO-08)

DWG. NO. 02Y00025-0350SHEET NO. 1 OF 6REL. 05/05/93 (m-df )For GPD 515, GPD 503, or GPD 575Adjustable Frequency Drivesor VCD 703Vector Control Drives

Page 2 - REL. 05/05/93 (m-df )

DWG. NO. 02Y00025-0350SHEET NO. 2 OF 6REL. 05/05/93 (m-df )Refer to Sheet 1 for latest change.Table 1. SpecificationsOutput Method Available Outputs

Page 3 - SHEET NO. 3 OF 6

DWG. NO. 02Y00025-0350SHEET NO. 3 OF 6REL. 05/05/93 (m-df )Refer to Sheet 1 for latest change. Figure 3. Interconnection for Digital Output (DO-08) C

Page 4

DWG. NO. 02Y00025-0350SHEET NO. 4 OF 6REL. 05/05/93 (m-df )Refer to Sheet 1 for latest change.CAUTIONTO PREVENT ERRONEOUS OPERATION CAUSED BY NOISEINT

Page 5 - SHEET NO. 5 OF 6

Refer to Sheet 1 for latest change. DWG. NO. 02Y00025-0350SHEET NO. 5 OF 6REL. 05/05/93 (m-df )Table 5. Programming For DO-08 OutputsSn-27 OutputSet

Page 6 - SHEET NO. 6 OF 6

DWG. NO. 02Y00025-0350SHEET NO. 6 OF 6REL. 05/05/93 (m-df )Refer to Sheet 1 for latest change.Table 6 Function of DO-08 Coded Output From GPD 503, G

Comments to this Manuals

No comments

Yaskawa DS383 User Manual

Browse online or download User Manual for Equipment Yaskawa DS383. Yaskawa DS383 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Equipment Yaskawa DS383