Yaskawa 120 Series I/O Modules User Manual Page 38
- Page / 308
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3 Digital I/O Specifications
3.1.2 200-VAC 16-point Input Module
3-8
3) The following diagram shows an example of terminal connections.
Connect power supplies of the same phase to the Common 1 and Common 2.
If power supplies of different phases are connected, overheating or fire may
occur.
Note: (1) Crimp Terminals
Use M3 terminal for crimping to the terminal block.
(2) Recommended Wires
Use wires of 1.3 mm
2
(AWG16) to 0.5mm
2
(AWG20) to connect to the terminal
block.
(3) Terminal 10 and terminal 20 are not connected.
Input 1
Input 2
Input 3
Input 4
Input 5
Input 6
Input 7
Input 8
Common 1
Not connected.
Input 9
Input 10
Input 11
Input 12
Input 13
Input 14
Input 15
Input 16
Common 2
Not connected.200 VAC
Terminals
EXAMPLE
CAUTION
- 120-SERIES I/O MODULES 1
- Manual Contents 2
- Visual Aids 2
- CONTENTS 3
- Introduction and Precautions 6
- 1.1 Overview of Manual 7
- 1.2 Precautions 8
- 1.2.1 Safety Precautions 8
- 1.2.3 Removal Precautions 10
- 1.2.4 Wiring Precautions 11
- 1.2 Precautions 12
- 1.2.4 Wiring Precautions 13
- Power Supply Noise Reduction 14
- 1.2.5 Application Precautions 16
- CPU Module 17
- Output Module 17
- 1.2.6 Maintenance 19
- 1.3 Using This Manual 20
- Modules 21
- 2.1 General Specifications 22
- 2.2 I/O Modules 23
- 2.2.1 Models of I/O Modules 23
- 2.2.1 Models of I/O Modules 24
- 1) Digital Input Modules 25
- 2) Analog Input Modules 26
- 3) Digital Output Modules 27
- 4) Analog Output Module 29
- 2.2.3 Using I/O Modules 30
- Digital I/O Specifications 31
- 4) External Appearance 35
- Internal circuits 41
- Not connected 42
- 12/24 VDC 42
- Photocoupler 45
- ACTIVE Green Processing I/O 47
- Indicator Switch 53
- and ground 62
- 5) Spare Parts 69
- Output signal 75
- 5) External Appearance 89
- 3.3 I/O Module Cables 90
- 3.3.1 I/O Module Cable Types 90
- 2) 64-point I/O Module Cables 91
- Connector on 94
- Shielded cable 94
- Loose wire side 94
- Wire No 94
- Connector 1 (Module side) 98
- Model name 98
- 3 Digital I/O Specifications 100
- 2) Approximate Specifications 101
- 3) External Appearance 102
- 3.3 I/O Module Cables 103
- 2) Specifications 104
- 3) Appearance 104
- 3.4 I/O Allocation 111
- 3.4.1 16-point Input Modules 111
- 4) I/O Data Format 112
- IMPORTANT 113
- 3.4.2 32-point Input Modules 114
- 3.4.3 64-point Input Modules 117
- 2) Module Type Setting 118
- 3.4.4 8-point Output Modules 122
- 3.4.5 16-point Output Modules 124
- 3.4.6 32-point Output Modules 127
- 3.4.7 64-point Output Modules 131
- 3.4 I/O Allocation 135
- 3.5 Operations Using MEMOSOFT 136
- 3.5.4 I/O Allocations 139
- 2) Setting the Module Type 140
- Input 000017 141
- 3.5.4 I/O Allocations 142
- 4) Setting the Data Type 143
- 5) Setting the Bit Order 144
- 6) Setting the Service Scan 145
- Input 100 147
- Analog I/O Specifications 148
- 1) Performance Specifications 149
- 2) Input Characteristics 150
- 4 Analog I/O Specifications 151
- 5) I/O Allocation 153
- 10 V, 4 CH). For 153
- 6) External Appearance 154
- Input register value 156
- Analog input value (V) 156
- 0-4000 mode 156
- Analog input value (mA) 162
- 2) Output Characteristics 168
- VER. C or later 169
- (0 to 5 V, 2 channels) 172
- Analog output value(V) 173
- Output register value 173
- LED Area 176
- 120 AVO 011 00 176
- C or later 179
- 4.3 I/O Allocation 182
- 4.3.1 Analog Input Modules 182
- 4.3.1 Analog Input Modules 183
- 4.3 I/O Allocation 184
- 4.3.2 Analog Output Modules 186
- 4.3.2 Analog Output Modules 187
- 4.4 Operations Using MEMOSOFT 188
- 4.4.3 I/O Allocations 190
- Fig. 4.8 I/O Map 192
- Fig. 4.9 Module Selection 192
- Input 300011 193
- Input 300012 193
- 4) Setting the Mode 194
- 5) Setting the Service Scan 194
- 4.4.3 I/O Allocations 195
- Register I/O Specifications 199
- 5.1.1 Register Input Modules 200
- 5.1.1 Register Input Modules 202
- LED Color Indication when ON 203
- 5.2.1 Register Output Modules 204
- 5.3 I/O Allocation 208
- 5.3.1 Register Input Modules 208
- 4) Parameter Setting 209
- 5.3.1 Register Input Modules 210
- 5.3.2 Register Output Modules 211
- Fig. 5.2 Data Output Timing 214
- 5.4 Operations Using MEMOSOFT 215
- 5.4.3 I/O Allocations 218
- Fig. 5.9 I/O Map Selection 219
- Fig. 5.10 I/O Map 219
- Input 400011 220
- Input 400020 221
- 4) Service Scan Setting 222
- 6) Mode Setting 224
- 7) Cycle Setting 225
- Fig. 5.25 Timing T1 Setting 226
- Installation and Wiring 228
- 6.1 Installing Modules 229
- 6.1 Installing Modules 230
- 6 Installation and Wiring 231
- Module hook 232
- Module connector 232
- Mounting Base 233
- 4) Removing Modules 235
- 6.2 Panel Wiring 240
- 6.2.2 Wiring AC I/O Modules 241
- JAMSC-120DAI54300 242
- JAMSC-120DAO84300 243
- 6.2.3 Wiring DC I/O Modules 244
- 6.2.3 Wiring DC I/O Modules 245
- JAMSC-120DDI34300 246
- JAMSC-120DDO34310 246
- Terminal Blocks 247
- 6.2 Panel Wiring 248
- 5) Protective Fuses 252
- 1) I/O Signal Cables 252
- 6.2.5 Grounding 255
- 5) Grounding Method 257
- 6.3 External Wiring 258
- 6.4 Precautions on Wiring 259
- 6.4.1 AC Input Modules 259
- 6.4 Precautions on Wiring 260
- 6.4.1 AC Input Modules 261
- 6.4.2 AC Output Modules 262
- 2) Protective Fuses 263
- 4) Maximum Load Current 264
- 6.4.2 AC Output Modules 265
- 6.4.3 DC Input Modules 267
- 6.4.3 DC Input Modules 269
- 6.4.4 DC Output Modules 272
- 6.4.4 DC Output Modules 275
- 6.4.7 Analog Input Modules 277
- 6.4.8 Analog Output Modules 278
- Maintenance 280
- 7.1 Built-in Fuses 281
- 7.1.2 Built-in Fuses 282
- 3) DC 16-point Output Module 283
- 4) DC 32-point Output Modules 283
- 5) DC 64-point Output Modules 284
- 2) Replacement Procedure 284
- 7.2 Hot Swapping 285
- 7.2.1 Hot Swapping 285
- 7.2 Hot Swapping 286
- 7 Maintenance 287
- 7.2.1 Hot Swapping 287
- Compliant I/O Modules 288
- 8.1.2 External Appearances 290
- 2) AC Output Module 291
- 8.1.3 EN Standards 292
- Crimp terminal 293
- Parallel to 293
- Appendix A 300
- A.1 I/O Module Types 301
- A.3 DC 32-point I/O Modules 302
- A.4 DC 64-point I/O Modules 303
- A.5 Register I/O Modules 303
- Numerics 304
Related products and manuals for Equipment Yaskawa 120 Series I/O Modules
Equipment Yaskawa A1000 AC Drive User Manual
(16 pages)
(16 pages)
Equipment Yaskawa Σ-7 Series User Manual
(1 pages)
(1 pages)
Equipment Yaskawa JAPMC-CM2304-E User Manual
(97 pages)
(97 pages)
Equipment Yaskawa Σ-II Series User Manual
(37 pages)
(37 pages)
Equipment Yaskawa Σ-mini Series User Manual
(26 pages)
(26 pages)
Equipment Yaskawa Σ-III Series User Manual
(37 pages)
(37 pages)
Equipment Yaskawa Σ-II Series User Manual
(31 pages)
(31 pages)
Equipment Yaskawa AO-12B2 User Manual
(16 pages)
(16 pages)
Equipment Yaskawa APOGEE FLN User Manual
(31 pages)
(31 pages)
Equipment Yaskawa AOI User Manual
(22 pages)
(22 pages)
© 2020, manymanuals.com. All rights reserved. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals