YASKAWA VS-626M5 Specifications Page 156
- Page / 301
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
The VS-626M5 PC NC Maintenance Manual
4-135
The figures below show the display section and operation keys of
the digital operator, and the LED display status of the RUN and
STOP keys. Table 4.31 shows the displayed characters and the
corresponding alphabets and numbers, and Figure 4.24 shows the
display of bit selection signal.
Figure 4.22: Display Unit and Operation Keys of the Digital Operator
LOCAL
REMOTE
DIGITAL OPERATOR
JVOP-132
DSPL
DATA
ENTER
JOG
FWD
REV
RESET
RUN STOP
DRIVE FWD REV
REMOTE
REFSEQ
DRIVE
PRGM
Mode Display LED
Display
Display Selection Key
JOG
DRIVE FWD REV REMOTE
REFSEQ
Digital Operator Running Indicati
o
Lights in the digital operator operation mod
e
Rotation Direction Indication
FWD: Lights when forward run command i
s
@@ input.
REV: Lights when reverse run command is
@@ input.
Remote Mode Indication
SEQ: Lights when the motor rotates in the
@@ reverse direction.
REF: * * *
Displays monitored values of speed referenc
e
and function set values.
Depress this key to select display ite
m
Read/Write Key
Depress this key to display set values of
constants. Depress this key again to write
set values.
Numeral Change Key
Use these keys to change values such as set
values and constant Nos.
È: Increment key
É: Decrement key
Digit Selection Key
Use this key to select a position in a set valu
e
to be changed. The selected position blinks.
(Use this key to reset after and error occurs.)
R
un Command Key
These are run command keys when the drive is oper
ated by the digital operator. These keys are effective
only in operation by digital operator.
STOP: Stop command
@@When STOP is depressed, the red LED on
@@the left part of the key lights.
RUN: Run command
@@When RUN is depressed, the red LED on
@@the left part of the key lights.
FWD/REV: Forward and reverse rotation switch
@@When this key is depressed, direction of
@@@rotation is changed.
JOG: Jog run
@@When this key is held down, jog run is available.
DRIVE/PRGM: Emergency stop
@@When this key is depressed, the operation speed
@@@is reduced and stopped. Then current is interrupted.
- YASNAC PC NC 1
- Maintenance Manual 1
- Contents 2
- Electrical Connection 4
- PC NC case 5
- Connection Between Devices 6
- Connector Layout NC Side 7
- NAC JZNC-JFC10 board 7
- 1.2 General Specifications 8
- All dimensions in millimeters 9
- 246 10
- 6 x 4.16 10
- Table 1.3: Heat Generation 12
- 2.1 Routine Inspection 14
- 2.2 Battery 14
- 2.3 Servo Motor 16
- 2.5 Touch Screen 18
- 2.6 Control Panel 19
- Chapter 4: Troubleshooting 22
- Troubleshooting (1) 25
- Table 4.11: Jog Feedrate 42
- Deceleration switch signal 46
- (*DCX signal) 46
- Figure 4.2: Spindle Rotation 49
- During boot up of the PC NC 53
- 01:Overcurrent 56
- 05: Overload 57
- 11:Output overvoltage 57
- 12:Power circuit low voltage 58
- F0:ROM is defective 62
- F1:EEPROM is defective 62
- F5:CPU is defective 63
- .. : Control card fault 63
- AL-01:Overcurrent 68
- AL-02:Ground fault 69
- AL-31:Motor overspeed 75
- AL-33:The load is abnormal 76
- AL-60:Tuning incompletion 80
- AL-65:INC signal error 83
- AL-A4:YENET1200 card error 3 87
- AL-F0:ROM is defective 92
- AL-F2:EEPROM is defective 2 93
- AL-F3:EEPROM is defective 3 93
- AL-F4:EEPROM is defective 4 93
- The motor does not rotate 95
- The motor reverses 96
- The motor does not stop 97
- Cause and measures 100
- The VS-626M5 101
- Operation 103
- Operation Of Digital Operator 104
- Maintenance and Inspection 105
- 4.3 Receiving 107
- 2 7P5 5 E * 108
- Upper and Lower Covers Opened 109
- 4.4 Installation 111
- Heat Sink 112
- (a) Front View (b) Side View 112
- (a) Front View 113
- (b) Side View 113
- 4.5 Wiring 114
- AC Reactor (L) (Note) 115
- P1N1 Power Cable 116
- A general-purpose noise 119
- Figure 4.14: Grounding 122
- 7. Main Circuit Configuration 125
- 8. Parts Required for Wiring 129
- 9. Control Signal Connectors 135
- Wiring The Control Circuit 137
- 1. Control Signals 137
- 51CN 5CN, 52CN 143
- 3CN (Option) 144
- (a) 0V Common 146
- (b) +24V Common 146
- (c) External Common 146
- 4.6 Operation 149
- (a)@Flange-mounted Type 150
- (b)@Foot-mounted Type 150
- Run Command 151
- (Fault occurrence No.) 152
- 4.7 Digital Operator 154
- RUN STOP 156
- Note: “—” is not displayed 157
- Numbers Letters 157
- 65432 10 158
- Display Example 166
- 626M5 and the VS-656MR5 168
- 4.9 Troubleshooting 170
- Fault Cause Corrective Action 177
- Chapter 5: Adjustments 181
- Location Explanation 182
- 6.1 CPU Rack 183
- 6.2 CRT Display Unit 190
- 6.3 Floppy Disk Drive Unit 199
- 6.4 NC Power Supply 200
- 6.6 Noise Filter 202
- Chapter 7: Memory Option 203
- 8.1 NC Data Handling 205
- Restore Kit Contents 235
- 1. External CD ROM Drive 235
- • EXP computer, INC CD-865 235
- 26. Click the Next button 243
- 7. Touch the Close button 250
- 10. Touch the Start button 253
- Common Instructions 254
- Next button 254
- Yes button to agree 255
- 8.4 CNC Card Software Update 274
- ON < 275
- 8.5 Manual Page Customization 284
Related products and manuals for Power adapters & inverters YASKAWA VS-626M5
(72 pages)
(122 pages)© 2020, manymanuals.com. All rights reserved. | 0.396 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals