YASKAWA VS MINI J7 User Manual Page 81
- Page / 177
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
67
Multi-function I/0 Chapter 5-9
5-9-2 Multi-function Output
The J7AZ incorporates two multi-function output terminals (MA and MB).
Output from these terminals has a variety of functions according to the
application.
Selecting the Multi-function Output (n40)
Note Do not set values outside the above setting ranges.
Set Values
Note Use “operation in progress” (set value: 1) or “idling“ (set value: 3) setting for
the timing for stopping the motor using a brake. To specify a precise stop
timing, set “frequency detection 1” (set value: 4) or “frequency detection 2”
(set value: 5), and set the frequency detection level (n58).
n40 Multi-function Output (MA/MB and MC) Changes during
operation
No
Setting
range
0 to 7, 10 to 17
(see note)
Unit of
setting
1 Default setting 1
Value Function Description
0 Fault output ON: Fault output (with protective function working)
1 Operation in progress ON: Operation in progress (with RUN command input or inverter output)
2 Frequency detection ON: Frequency detection (with frequency reference coinciding with output
frequency)
3 Idling ON: Idling (at less than min. output frequency)
4 Frequency detection 1 ON: Output frequency ≥ frequency detection level (n58)
5 Frequency detection 2 ON: Output frequency ≤frequency detection level (n58)
6 Overtorque being monitored
(NO-contact output)
Output if any of the following parameter conditions is satisfied.
• Overtorque detection function selection (n59)
• Overtorque detection level (n60)Overtorque detection level (n60)
• Overtorque detection time (n61)
Note NO contact: ON with overtorque being detected;
NC contact: OFF with overtorque being detected
7 Overtorque being monitored
(NC-contact output)
10 Alarm output ON: Alarm being detected (Nonfatal error being detected)
11 Base block in progress ON: Base block in progress (in operation with output shutoff)
12 RUN mode ON: Local mode (with the Digital Operator)
13 Inverter ready ON: Inverter ready to operate (with no fault detected)
14 Fault retry ON: Fault retry (Inverter resetting with fault retry (n48) not set to 0)
15 UV in progress ON: Undervoltage being monitored
(main circuit undervoltage UV or UV1 detected)
16 Rotating in reverse direction ON: Rotating in reverse direction
17 Speed search in progress ON: Speed search in progress
- 1
- 1
- Visual Aids 3
- General Precautions 4
- Wiring Precautions 5
- Transportation Precautions 5
- Installation Precautions 5
- Warning Labels 7
- CIMR—J7AZ20P1 8
- About this Manual 9
- Application Considerations 10
- Disclaimers 11
- Table of Contents 13
- CHAPTER 1 15
- Overview 15
- 1-1 Function 16
- 1-2 Nomenclature 17
- Nomenclature Chapter 1-2 18
- Digital Operator 18
- CHAPTER 2 19
- 2-1 Installation 20
- Installation Chapter 2-1 21
- 2-2 Wiring 24
- Wiring Chapter 2-2 25
- Removing the Front Cover 25
- 2-2-2 Terminal Block 26
- Main Circuit Terminals 27
- Control Circuit Terminals 28
- Selecting Input Method 28
- 2-2-3 Standard Connections 30
- Circuit Breaker Capacities 31
- Wiring Example 1 34
- Ground Wiring 37
- Harmonics 38
- Standard Connection 43
- LVD Conformance 45
- CHAPTER 3 47
- 3-1 Nomenclature 48
- 3-2 Outline of Operation 49
- Status Monitor 51
- Example of Paramter Settings 53
- CHAPTER 4 55
- Test Run 55
- Chapter 4 56
- 4-1 Procedure for Test Run 57
- 4-2 Operation Example 59
- 4-2-3 Initializing Parameters 60
- 4-2-5 No-load Operation 61
- 4-2-6 Actual Load Operation 62
- CHAPTER 5 63
- Basic Operation 63
- 5-1 Initial Settings 64
- 5-2 V/f Control 65
- V/f Control Chapter 5-2 66
- Basic Conecpt 67
- 5-9 Multi-function I/0 77
- Set Values 78
- Forward (reverse) 80
- RUN command 80
- 5-9-2 Multi-function Output 81
- 5-10 Analog Monitor Output 82
- CHAPTER 6 83
- Advanced Operation 83
- 6-3 Stall Prevention Function 87
- 6-7 Other Functions 93
- 6-7-4 Fault Retry (n48) 95
- Frequency Detection 97
- Other Functions Chapter 6-7 100
- 6-7-8 Error History (n78) 101
- CHAPTER 7 103
- Communications 103
- 7-1-1 Overview 104
- 7-1-2 External Dimensions 104
- 7-1-3 Names of Parts 105
- 7-1-4 Mouting Procedure 105
- Connector 106
- 7-2 Inverter Settings 107
- Inverter Settings Chapter 7-2 108
- Slave Address (n70) 108
- Send Wait Time Setting (n73) 109
- RTS Control Selection (n74) 109
- Communications Format 112
- Message Interval 112
- Message Data Configuration 112
- Slave Address 113
- Function Code 113
- Communications Data 113
- Error Check 114
- 7-4 DSR Message and Response 115
- Response 116
- Example of Data Read 116
- Settings and Response 117
- Example of Loop-back Test 121
- 7-5 Enter Command 122
- Converting the Register Data 123
- Bit reversed 124
- 1 is added 124
- 7-7-1 I/O Function 125
- 7-7-2 Monitor Functions 126
- Errors and Remedies 129
- 7-9 Self-diagnostic Test 130
- CHAPTER 8 131
- Fault Displays and Processing 132
- 8-2 Troubleshooting 137
- 8-2-6 Motor Burns 139
- 8-2-9 Mechanical Vibration 140
- 8-2-13 Inverter Does Not Run 141
- Daily Inspection 142
- Periodic Inspection 142
- Periodic Maintenance Parts 143
- Replacement of Cooling Fan 143
- CHAPTER 9 145
- Specifications 145
- 9-1 Inverter Specifications 146
- 9-2-1 List of Accessories 149
- 9-2-2 Adapter Panel 150
- 9-2-4 Fan Unit 151
- 9-2-5 Digital Operator 152
- 9-2-6 Digital Operator Case 153
- 9-2-8 DC Reactor 153
- 3G3IV-PEZZ08122_ 154
- Applicable Model 154
- External Dimensions (mm) 154
- 9-2-10 AC Reactor 155
- 9-3 Option Specifications 156
- External Dimensions 157
- CHAPTER 10 159
- List of Parameters 159
- List of Parameters Chapter 10 160
- CHAPTER 11 173
- Revision History 176
Related products and manuals for Power adapters & inverters YASKAWA VS MINI J7
(8 pages)© 2020, manymanuals.com. All rights reserved. | 1.238 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals