TM.IW.01 USER’S MANUAL InverterWin REV 3.0 AC Inverter Support Software For GPD505/P5 and GPD506/P5
Installation Chapter 2 6 TM.IW.01 2-1 PC Requirements !!!! InverterWin AC Inverter Sup
Installation Chapter 2 7 TM.IW.01 !!!! InverterWin Software Installation from ZIP File
Installation Chapter 2 8 TM.IW.01 2-3 Connecting the PC to the Inverter !!!! InverterWin
Installation Chapter 2 9 TM.IW.01 2-4 Getting Started !!!! Starting InverterWin The fol
Installation Chapter 2 10 TM.IW.01 2-5 Going Online with the Inverter • To start the online
Installation Chapter 2 11 TM.IW.01 A Device Selection window with a list of all of the inverter
Installation Chapter 2 12 TM.IW.01 Figure 2.6: Main Online Screen If the inverter loses p
Installation Chapter 2 13 TM.IW.01 2-6 Going Offline with the Inverter Once connected or onl
CChhaapptteerr 33 •••• Operation •••• 3-1 Uploading and Downloading Parameters 3-2 Opening an Existing Parameter File 3
15 TM.IW.01 3-1 Uploading and Downloading Parameters Before inverter parameters can be uploaded or downloaded, the inverter product type must be se
ii TM.IW.01 Thank you for choosing this YASKAWA ELECTRIC AMERICA software product. Proper installation and use of this software will ensure proper
16 TM.IW.01 3-2 Opening an Existing Parameter File To open an existing file for the current inverter product click on the file open icon or
17 TM.IW.01 3-3 Saving a Parameter File To save the current parameter file to floppy or hard drive, click on the file save icon or select F
18 TM.IW.01 3-5 Parameter File Information When viewing a parameter file, a window similar to the one below (Figure. 3.3) will be displayed.
19 TM.IW.01 3-6 Graphing Inverter Operation The Graph function tab is used to graphically plot drive monitor constants during drive operation. S
20 TM.IW.01 After the trace selection has been made, click on OK to display the trace selections next to the graph. The Inverter
21 TM.IW.01 Once monitor mode is enabled and trace selection is completed, a screen similar to Figure 3.7 will appear: Figure 3.7: Main Graph Dis
22 TM.IW.01 !!!! Adjusting the Scale & Timeline When the graph is tracking, the scale may be adjusted by “pulling” on the anchors on the X and
23 TM.IW.01 3-7 Inverter Fault History The InverterWin software may be used to upload the fault history of the inverter. The information held
24 TM.IW.01 To retrieve the fault history information from the inverter, click on the Update button and the function will retrieve the fault history
25 TM.IW.01 3-8 Monitoring Inverter Operation The InverterWin software may be used to monitor status of the inverter at any point while it is onli
iii TM.IW.01 Notice: YASKAWA ELECTRIC AMERICA products are created and manufactured for use according to proper procedures by a qualified operator an
26 TM.IW.01 !!!! Setting up the Monitor Panel To set up the monitor panels, click on the monitor bar setup icon or click on View > Monitor Bar
27 TM.IW.01 Parameter Name Function Range/Scale Comment Frequency Reference Main frequency reference inside inverter 0 – max Hz Output Frequen
28 TM.IW.01 3-9 Other Menu Options InverterWin contains menu options that are not found on the icon toolbar. Some of the more common menu option
29 TM.IW.01 3-10 Status Bar InverterWin provides a status bar than displays important information about the software, and about the connected inv
30 TM.IW.01 !!!! Status Bar Details Figure 3.18: Right Hand Side Detail of Status Bar 1. Model: This is the model number of the invert
•••• Appendix •••• 4-1 Software Revision History 4-2 Toolbar Icons 4-3 Troubleshooting
32 4-1 Software Revision History !!!! InvWin Revision 2.12 1) Eliminated Parameter save issues when in the offline mode. !!!! InvWin
33 4-3 Troubleshooting Error Message or Symptom Cause Solution Software does not install $ Minimum hardware requirements may not be met $ Upgr
iv TM.IW.01 Contents 1 Overview ... 1-1 Introduction...
CChhaapptteerr 11 •••• Overview •••• 1-1 Introduction 1-2 Nomenclature 1-3 New Features for 3.00
2 TM.IW.01 1-1 Introduction !!!! InverterWin AC Inverter Support Software The YASKAWA ELECTRIC AMERICA InverterWin support tool is a Windows
3 TM.IW.01 1-2 Nomenclature Menu Bar Toolbar Monitor Panel Selection Tabs Main Window Status Bar Figure 1.1: InverterWin Screen Nomenclatu
4 TM.IW.01 1-3 New Features for InverterWin 3.00 The following are new features and changes from InverterWin 2.12 to InverterWin 3.00 1. Th
CChhaapptteerr 22 •••• Installation •••• 2-1 PC Requirements 2-2 Installation 2-3 Connecting the PC 2-4 Getting Started 2-5
Comments to this Manuals