MANUAL NO. TOBP C880700 02M形式MP2200/MP23/MP2400マシンコントローラ安全上のご注意製品を安全にお使い頂くために,本書を必ずお読みください。また,本書をお手元に保管していただくとともに,最終的に本製品をご使用になるユーザー様のお手元に確実に届けられる
E-8Note: 1. Depending on the combination of option modules in the MP2300, model number will vary. JEPMC-MP2300-Y : Arbitrary number2. Model
6 ReceivingE-9 Nameplate of Main Unit and Option UnitNameplates with the model and so on of the unit are located on the side of the unit.The followi
E-107 InstallationObserve the following precautions when installing MP2200/MP23/MP2400.• Install MP2200/MP23/MP2400 perpendicular to the wall
8 WiringE-118 WiringWhen using MP2000 series option output modules or option output units, if the Machine Controller main unit power supply is turne
E-12The power ON sequences and circuit configuration examples are as shown below. When the output is connected to Relay and SolenoidConfigure the ci
8 WiringE-13 When the output is connected to a CPU built-in module inputConnect the CPU RUN output (interlock output) of the MP2000 module to anothe
E-14 Intended Option Output ModulesThe intended option output modules are listed below.• JAPMC-IO2300 (-E) (LIO-01)• JAPMC-IO2301 (-E) (LIO-02)• J
9 InspectionE-159 InspectionThis section describes the MP2200/MP23/MP2400 basic inspections. MP2200/MP23/MP2400 InspectionFor inspections and
Revision HistoryThe revision dates and numbers of the revised manuals are given on the bottom of the back cover.MANUAL NO.ޓTOBP C880700 02BPublished i
November 2004−All chapters Addition: Model JEPMC-IO23, JAPMC-AN23, JAPMC-PL23, JAPMC-DO23June 2004−All chapters Addition: Model JAPMC-EX22Ap
Copyright © 2002 YASKAWA ELECTRIC CORPORATIONAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or tra
IRUMA BUSINESS CENTER (SOLUTION CENTER)480, Kamifujisawa, Iruma, Saitama 358-8555, JapanPhone 81-4-2962-5151 Fax 81-4-2962-6138http://www.yaskawa.
한국 전파법에 관한 주의사항韓国電波法に関連する注意事項Precautions for Korean Radio Waves Act针对韩国电波法的注意事项사용자 안내문기종별 사용자 안내문A급 기기( 업무용 방송 통신기 자재 )이 기기는 업무용 (A 급 ) 전자파 적합 기기로서 판매
1 IntroductionE-11 IntroductionThis safety precautions manual describes the MP2200/MP23/MP2400 Machine Control-ler. To properly use the MP2200/M
E-24 Safety InformationThe following conventions are used to indicate precautions in this manual. Failure to heed pre-cautions provided in this manua
5 Notes for Safe OperationE-35 Notes for Safe OperationRead this manual thoroughly before checking products on delivery, storage and transportation,
E-4 Storage and Transportation Installation• Do not store or install the product in the following places.• Locations subject to direct sunlight.• L
5 Notes for Safe OperationE-5 Wiring• Be sure to wire correctly and securely.Failure to observe this caution may result in motor overrun, injury, o
E-6 Maintenance and Inspection Disposal• Do not disassemble the unit. Failure to observe this caution may result in electric shock or injury.• Do
6 ReceivingE-76 ReceivingConfirm the model number of each product upon receiving the delivery.Products Abbrevia-tionModel OutlineMP2200Main UnitBase
Comments to this Manuals