Yaskawa MP3200 CPU User Manual

MANUAL NO. TOMP C880725 16A製品を安全にお使い頂くために，本書を必ずお読みください。また，本書をお手元に保管していただくとともに，最終的に本製品をご使用になるユーザー様のお手元に確実に届けられるよう，お取り計らい願います。To properly use the prod

E-8 Wiring• Check the wiring to be sure it has been performed correctly.There is a risk of motor run-away, injury, or accidents.• Always use a pow

E-9• Configure the circuits to turn ON the power supply to the CPU Unit before the 24-V I/O power supply. If the power supply to the CPU Unit is turne

E-10• Select the I/O signal wires for external wiring to con-nect the Machine Controller to external devices based on the following criteria:• Mech

E-11 Operation• Follow the procedures and instructions in the user’s manuals for the relevant products to perform normal operation and trial operatio

E-12 Maintenance and Inspection Disposal• Do not attempt to disassemble or repair the Machine Controller.There is a risk of electrical shock, inj

E-13 Other General Precautions• Observe all local laws and ordinances when you dis-pose of used Batteries.CAUTIONObserve the following general precau

E-14Warranty Details of Warranty Warranty PeriodThe warranty period for a product that was purchased (herein-after called “delivered product”) is

E-15• Causes that were not foreseeable with the scientific and technological understanding at the time of shipment from Yaskawa• Events for which Yask

E-16 Suitability for Use• It is the customer’s responsibility to confirm conformity with any standards, codes, or regulations that apply if the Ya

E-17• Never use the product for an application involving seri-ous risk to life or property without first ensuring that the system is designed to secur

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, mechan

E-18ContentsSafety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Warranty. . . . . . . . . . . . . . . . . . . . . . . . . .

1 Confirmations Upon DeliveryE-191Confirmations Upon DeliveryPlease confirm the following items as soon as you receive the Machine Controller.If you

1 Confirmations Upon Delivery E-20NameplateModel numberVersionSerial numberMAC address+0&%106'38'4/1&'./#%#&&

2 InstallationE-212InstallationRefer to the following manual for details on installing the Machine Controller.MP2000/MP3000 Series Machine Controller

2 Installation E-22Installation in locations subject to corrosive gasTake measures to prevent corrosive gas from entering the Machine Controller. Alt

3 WiringE-233WiringRefer to the following manual for details on connecting the Machine Controller.MP2000/MP3000 Series Machine Controller System Setu

3 Wiring E-24A power-ON sequence and an example circuit configuration are given below. Outputs Connected to Relays or SolenoidsConfigure circuits th

3 WiringE-25<Example Circuit Configuration>Note: The MP3200 includes the Power Supply Unit, CPU Unit, and Base Unit.The circuit configuration e

3 Wiring E-26 Outputs Connected to Other Input and Output DevicesConnect the CPU RUN output (interlock output) from the CPU Unit to other input and

3 WiringE-27<Example Circuit Configuration>* Design the circuits so that input and output signals from other input and output devices are used

E-1Safety PrecautionsThe following signal words and marks are used to indicate safety precautions in this manual.Information marked as shown below is

4 Inspections E-284InspectionsPerform inspections and part replacements according to the information that is provided in this section.Daily Inspectio

4 InspectionsE-29* MP3000-series MP3200/MP3300 Troubleshooting Manual(Manual No.: SIEP C880725 01)Indi-catorsRDY indi-catorCheck the status.Must be

4 Inspections E-30Periodic InspectionsPerform the following inspections at least once a year.* If the Machine Controller is installed in a panel, the

4 InspectionsE-31Replacement Guidelines for Machine Controller PartsElectrical and electronic parts have a limited service life due to mechanical wea

5 EMC Standard Compliance E-325EMC Standard ComplianceThe Machine Controller complies with the following EMC standards: EN 55011 group 1 class A, EN

E-33Revision HistoryThe revision dates and numbers of the revised manuals are given on the bottom of the back cover.MANUAL NO. TOMP C880725 16A <1

IRUMA BUSINESS CENTER (SOLUTION CENTER)480, Kamifujisawa, Iruma, Saitama, 358-8555, JapanPhone 81-4-2962-5151 Fax 81-4-2962-6138http://www.yaskawa

한국 전파법에 관한 주의사항韓国電波法に関連する注意事項Precautions for Korean Radio Waves Act针对韩国电波法的注意事项Précautions pour la Loi coréenne relative aux ondes radio사용자 안내문기종별 사용자

E-2The following precautions are for storage, transportation, installation, wiring, operation, maintenance, inspection, and disposal. These precaut

E-3 General Precautions• The installation must be suitable and it must be per-formed only by an experienced technician.There is a risk of electrical

E-4 Storage and Transportation• Do not store the Machine Controller in any of the fol-lowing locations.• Locations that are subject to direct sunl

E-5• If disinfectants or insecticides must be used to treat packing materials such as wooden frames, pallets, or plywood, the packing materials must b

E-6 Installation• Do not install the Machine Controller in any of the fol-lowing locations.• Locations that are subject to direct sunlight• Locati

E-7• Always mount the Machine Controller in the specified orientation.There is a risk of malfunction.• Leave the specified amount of space between the