Yaskawa iQpump1000 AC Drive Quick Start User Manual Page 103
- Page / 470
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
n
Flange Type Terminal and Wiring Specifications
Wire gauges and tightening torques
are identical to standard models.
Unit: in. [mm]
CONTROL
CIRCUIT
TERMINALS
MAIN CIRCUIT
TERMINALS
(2) GROUND
TERMINALS
SECTION A-A
DETAIL A
DETAIL A
Figure 2.56 Models 2A0360 and 2A0415, 4A0296 to 4A0362, and 5A0192 and 5A0242
2.2 Flange Type Enclosure (NEMA 12 Backside) Dimensions & Heat Loss
YASKAWA TOEP YAIP1W 01B YASKAWA AC Drive - iQpump1000 Quick Start Guide
103
2
Mechanical Installation
- Quick Start Guide 1
- Simple Setup Procedure 3
- Identification and Mounting 4
- Changing Parameters and 6
- Monitoring the iQpump 6
- P1-02 Feedback Unit 8
- START / DRAW DOWN LEVEL 8
- Start Pump System 8
- Auto/Hand Operation 9
- Auto Operation 9
- Go to Sleep 9
- FEEDBACK SIGNAL CHECK 10
- HAND MODE 11
- Table of Contents 13
- Preface & General Safety 21
- Applicable Documentation 22
- Terms and Abbreviations 22
- Trademarks 22
- Installation 27
- Settings 27
- General Handling 27
- Standard Induction Motors 28
- Specialized Motors 28
- Single-Phase Motor 29
- Restrictions 30
- Receiving 31
- Nameplate 32
- P W 2 A 33
- 2.1 Mechanical Installation 36
- Single Drive Installation 37
- Figure 2.7 38
- Remote Operation 40
- +0.5 (0.02) 42
- SECTION A-A 55
- Figure 2.26 Model 4A0031 67
- SECTION A-A 74
- Unit: in. [mm] 100
- FRONT VIEW 101
- Flange Type Heat Loss Data 102
- Mechanical Installation 103
- This Page Intentionally Blank 116
- Electrical Installation 117
- Removing the Jumper 123
- Application Notes 123
- 3.3 Terminal Cover 125
- Removing the Terminal Cover 126
- Removing the HOA Keypad 127
- Reattaching the HOA Keypad 127
- Removing the Front Cover 127
- HookHook 128
- Front cover 128
- Free hooks on both 128
- Reattaching the Front Cover 129
- 3.5 Top Protective Cover 130
- 3.6 Main Circuit Wiring 131
- Insulation Barrier 133
- Three-Phase 200 V Class 134
- Three-Phase 400 V Class 136
- Three-Phase 600 V Class 139
- Ground Wiring 141
- 3.7 Control Circuit Wiring 143
- Output Terminals 144
- Ferrule-Type Wire Terminals 146
- 3.8 Control I/O Connections 148
- Transducer Wiring 150
- 3.9 Connect to a PC 153
- Start-Up Checklist 156
- Start-Up Programming 157
- & Operation 157
- 4.2 Powering Up the Drive 158
- 4.3 Using the HOA Keypad 162
- LCD Display 163
- ALARM (ALM) LED Displays 164
- Menu Structure for HOA Keypad 166
- 4.4 Pump Application Presets 169
- G eo the rm al S lee p 180
- A1 A2 A3 182
- Current Limit 185
- Required Control Wiring 188
- P re -C ha rg e 192
- Pressure Feedback 196
- P1-01 = 1 196
- (Contactor Multiplex) 196
- RS-485 Network 197
- Process Supply 197
- Reservoir 197
- 100.0PSI 198
- U5-99= 100.0 199
- U1-01= 59.41 200
- U1-01= 55.00 200
- U1-01= 51.37 200
- U1-01= 48.00 200
- <1> 202
- Multiplexing Stop History 204
- De-Scale/De-Ragging 205
- A1-01: Access Level Selection 207
- A1-03: Initialize Parameters 207
- 2-Wire Control 208
- 3-Wire Control 208
- Jumper S1 210
- A1/A2/A3 210
- Voltage/Current 210
- Selection 210
- Figure 5.4 211
- E2-01: Motor Rated Current 216
- E2-04: Number of Motor Poles 216
- <2> 218
- P1-01: Pump Mode 223
- P1-02: System Units 224
- Setting 1: Alarm 226
- Setting 2: Digital out only 226
- P1-11: High Feedback Level 227
- P2-01: Sleep Level Type 228
- P2-02: Sleep Level 228
- P4-17: Utility Start Delay 233
- P5-02: HAND Reference 1 233
- 4.7 Test Run with No Load 236
- Checklist Before Operation 237
- Troubleshooting 239
- 5.2 Fault Detection 241
- 5.3 Alarm Detection 260
- Fault Reset Methods 284
- 5.8 Auto-Tuning 285
- Auto-Tuning Operation Example 286
- Entry Accepted 287
- Starting Auto-Tuning 288
- 6.1 Inspection 290
- Periodic Inspection & 291
- Maintenance 291
- 6.2 Periodic Maintenance 292
- Related Drive Parameters 293
- 6.3 Drive Replacement 294
- Installing the Drive 295
- 7.1 Option Card Installation 298
- NS MS 300
- TX RX 300
- Appendix: A 303
- A.1 Power Ratings 304
- Specifications 305
- A.2 Drive Specifications 313
- 2 <9> 314
- A.3 Drive Watt Loss Data 315
- A.4 Drive Derating Data 317
- Parameter Settings 322
- Altitude Derating 323
- Appendix: B 325
- OLVOLVOLVOLV 326
- A2: User Parameters 327
- Parameter List 327
- B.2 b: Application 328
- B.3 C: Tuning 334
- C6: Carrier Frequency 336
- B.4 d: References 337
- B.5 E: Motor Parameters 340
- E2: Motor 1 Parameters 341
- B.6 F: Options 343
- <1> 358
- H6: Pulse Train Input 359
- B.8 L: Protection Function 360
- L3: Stall Prevention 362
- L4: Speed Detection 363
- L5: Fault Restart 364
- L6: Torque Detection 365
- B.9 n: Special Adjustment 368
- B.11 P: Pump Parameters 373
- P2: Pump Protection 375
- P3: Contactor Multiplexing 377
- P4: Pump Advanced 379
- P5: Pump HAND Mode 381
- P6: Flow Meter Setup 382
- P7: Anti-Jam 384
- P8: De-Scale / De-Ragging 385
- P9: Network Options 385
- Q1: Preset Setpoint 390
- Q2: Geothermal Mode Setup 390
- Q3: Output Current Limit 391
- Q4: Water Level Control 391
- Q5: Suction Pressure Control 392
- B.13 S: Special Application 395
- S6: Protection 399
- B.15 U: Monitors 401
- 00000000 403
- U3: Fault History 405
- U4: Maintenance Monitors 406
- U5: PID Monitors 409
- Appendix: C 411
- Master (PLC or other) 412
- Slave (Drive) 412
- MEMOBUS/Modbus 413
- Communications 413
- IG R+ R- S+ S 414
- RS-485 Interface 415
- RS-422 Interface 416
- H5-07: RTS Control Selection 418
- Observing the Drive Operation 420
- Controlling the Drive 420
- C.6 Communications Timing 421
- C.7 Message Format 422
- D 1 4 0 423
- (Lower) (Upper) 423
- C.8 Message Examples 424
- Writing to Multiple Registers 425
- C.9 MEMOBUS/Modbus Data Table 426
- Monitor Data 428
- Broadcast Messages 440
- Fault Trace Contents 440
- Alarm Register Contents 442
- C.10 Enter Command 444
- C.11 Communication Errors 445
- C.12 Self-Diagnostics 446
- Appendix: D 447
- D.1 European Standards 448
- Grounding 450
- EMC Filter Installation 450
- Standards Compliance 451
- EMC Filters 453
- D.2 UL and CSA Standards 456
- Drive Short Circuit Rating 463
- Revision History 468
Related products and manuals for Equipment Yaskawa iQpump1000 AC Drive Quick Start
Equipment Yaskawa Matrix Converter User Manual
(398 pages)
(398 pages)
Equipment Yaskawa AC Drive Z1000 User Manual
(395 pages)
(395 pages)
Equipment Yaskawa CIMR-LU Drives User Manual
(242 pages)
(242 pages)
Equipment Yaskawa RC5 Converter User Manual
(69 pages)
(69 pages)
Equipment Yaskawa i80M Appendix User Manual
(339 pages)
(339 pages)
Equipment Yaskawa J50M Instructions User Manual
(298 pages)
(298 pages)
Equipment Yaskawa SI-W3 User Manual
(80 pages)
(80 pages)
© 2020, manymanuals.com. All rights reserved. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals