YASKAWA VS MINI J7 Instruction Manual Page 90
- Page / 138
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
6. Programming Features
89
VERIFY Function
This function compares the constants stored in the Digital Operator with
the constant in the Inverter. Verification is possible only for the Invert-
ers with same product series and power supply specifications.
When the constants stored in the Digital Operator are the same as those
in the Inverter, vFy will flash, and then End will be displayed.
Example: Comparing Constants Stored in EEPROM in Operator with
Constants in Inverter
While a constant No. that is not the same is displayed or a constant
value is displayed, press STOP/RESET to interrupt the execution of the
verification. End will be displayed. Press DSPL or ENTER to return to
the constant No.
Explanation Operator Display
• Enable the settings for
constants n01 to n79.
• Press DSPL to light
[PRGM].
• Press ENTER to display the
set value.
• Change the set value to 4
by pressing the or
key.
• Press ENTER.
(May be a different constant No.)
(Lit)
(May be a different constant No.)
(Flashes)
(Lit for one second.)
↓
(The constant No. is displayed.)
• Execute VERIFY by
Constant Copy Function
Selection (n76).
• Change the constant No. to
n76 by pressing the or
key.
• Press ENTER to display the
set value.
• Change the set value to vFy
by pressing the or
key.
• Press ENTER.
(Lit)
(Lit)
(Flashes while executing VERI-
FY)
• Display the unmatched
constant No.
(Flashes) (When n011 is differ-
ent.)
• Display the constant
value in the Inverter.
• Press ENTER.
(Flashes)
• Display the constant
value in the Digital
Operator.
• Press ENTER.
(Flashes)
• Continue the execution
of VERIFY.
• Press the key.
• Press DSPL or ENTER.
(Flashes while executing the
verification)
↓
(End is displayed when the verifi-
cation has been completed.)
(The constant No. is displayed.)
- INSTRUCTION MANUAL 1
- General Precautions 2
- PRECAUTIONS FOR CE MARKINGS 4
- RECEIVING THE PRODUCT 5
- MOUNTING 5
- OPERATION 8
- MAINTENANCE AND INSPECTION 10
- (Ref. page) 11
- WARNING LABEL 12
- WARRANTY INFORMATION 14
- RESTRICTIONS 15
- CONTENTS 16
- 1. Receiving the Product 20
- 2. Identifying the Parts 21
- 3. Mounting 22
- Mounting Dimensions 23
- 4. Wiring 25
- 2. Main Circuits 27
- Wiring the Main Circuits 30
- • Inverter Output 31
- Wiring the Control Circuits 32
- Wiring Inspection 33
- 5. Operating the Inverter 34
- Operation Check Points 35
- Multi-function monitoring 39
- Selecting the Monitor 40
- Input terminal status 41
- Output terminal status 41
- Simple Data Setting 42
- or key 43
- 6. Programming Features 44
- * 2. Refer to page 70 45
- Selecting V/f Pattern 46
- Motor Specification: 60 Hz 47
- (Factory setting) 47
- Motor Specification: 50 Hz 47
- Switching LOCAL/REMOTE Mode 49
- Selecting RUN/STOP Commands 50
- Setting by Operator 51
- LOCAL Mode 51
- REMOTE Mode 51
- 8-step speed change 52
- Operating at Low Speed 53
- Max. frequency (100 %) 55
- Gain n41 = 100 55
- Bias n42 = 50 55
- S-curve Selection (n20) 57
- Torque Detection 58
- Frequency Detection 1 60
- Frequency Detection 2 60
- SPEED SEARCH Command 62
- Command Input 63
- Deceleration to a Stop 68
- Coast to a Stop 69
- Using Input Signals 70
- Initial Settings 71
- RUN command 71
- (Setting: 18) 74
- Using Output Signals (n40) 74
- No. Terminal Initial Setting 75
- Current Reference Selection 77
- Output frequency 79
- Slip Compensation 81
- Motor Protection 82
- Communications Specifications 85
- Constant Copy Function 85
- READ Function 87
- COPY Function 88
- VERIFY Function 90
- Inverter Capacity Display 91
- Software No. Display 92
- Display List 92
- Periodic Inspection 94
- Part Replacement 95
- Replacement of Cooling Fan 96
- 1. Removal 96
- 2. Mounting 96
- Flashing 99
- 8. Fault Diagnosis 100
- Fault Displays and Meanings 101
- Troubleshooting 105
- 9. Specifications 107
- Standard Wiring 114
- Terminal Descriptions 115
- Transistor 116
- • 200 V Single-phase 121
- • 400 A 3-phase 121
- Surge Suppressors 122
- Constants List 123
- • 200 V Class 3-phase 129
- • 200 V Class Single-phase 129
- • 400 V Class 3-phase 129
- CE Markings 130
- EMC Directive 131
- Installation Method 131
- EMC Noise Filter 134
- CIMR-J7 135
- Revision History 136
- Max. output voltage in the 137
Related products and manuals for Power adapters & inverters YASKAWA VS MINI J7
(218 pages)
(122 pages)© 2020, manymanuals.com. All rights reserved. | 0.651 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals