YASKAWA NX100 Operator's Manual Page 262
- Page / 297
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2.7 Arc Welding Instruction
2-240
1. WELD1/WELD2/WELD3/WELD4
Choose one of the tags from the following table. These tags are valid for a system with multi-
ple applications in which two or more arc welding applications are included. These tags are
not displayed when there is only one application
.
2. AC=Current output value
The following tag can be added or omitted.
3. AV=Voltage output value/AVP=Ratio to proper voltage output value
Choose one of the tags from the following table.
No. Tag Explanation Note
1
WELD1 Specifies Welder 1.
2
WELD2 Specifies Welder 2.
3
WELD3 Specifies Welder 3.
4
WELD4 Specifies Welder 4.
No. Tag Explanation Note
5
AC=Current out-
put value
Specifies the output value of the welding current. Current value:
1 to 999 A
Variable B/I/D/B[]/I[]/
D[]/LB/LI/LD/LB[]/
LI[]/LD[] can be used.
No. Tag Explanation Note
6
AV=Voltage out-
put value
Specifies the output value of the arc voltage.
When the welder power supply is ’Individual’, the
output value of the arc voltage is specified.
Voltage value:
0.1V to 50.0 V
Variable B/I/D/B[]/I[]/
D[]/LB/LI/LD/LB[]/
LI[]/LD[] can be used.
(Units: 0.1V)
7
AVP=Ratio to
proper voltage
output value
Specifies the ratio to the aptitude output value of
the arc voltage.
When the welder power supply is ’Same’, the
ratio to the aptitude output value of the arc volt-
age is specified.
Ratio: 50% to 150%
Variable B/I/D/B[]/I[]/
D[]/LB/LI/LD/LB[]/
LI[]/LD[] can be used.
Explanation
- INFORM MANUAL 1
- MANDATORY 2
- PROHIBITED 3
- Emergency Stop Button 4
- Equipment Manual Designation 5
- NX100 Controller NX100 5
- 1 INFORM Manual Outline 7
- 2 INFORM Explanation 7
- 1 INFORM Manual Outline 9
- 1.1.3 Instruction Set 10
- MainMenu 11
- ShortCut 11
- MainMenu ShortCut 11
- 1.2.1 Registration 12
- 1.2.2 Learning Function 13
- [SELECT] is pressed 14
- Operation Explanation 14
- 1.3 Detail Edit Window 15
- 1.4.1 Expression 16
- ) )) ))) 17
- 1.4.2 Registration 18
- Main Menu Short Cut 19
- 1.5 INFORM Structure 20
- INFORM Structure Elements 21
- Meaning of INFORM Structure 21
- Explanation Table 22
- 2 INFORM Explanation 23
- OGH#(1)OGH#(2) 24
- OT#(17)OT#(23) OT#(22) 25
- IGH#(1)IGH#(2) 27
- 2.1 I/O Instructions 28
- Pulse signal 36
- Analog output 37
- Output voltage 37
- 3. V=Basic speed 39
- 4. OFV=Offset voltage 39
- Motion speed 40
- Basic speed 40
- Basic viltage 40
- Offset voltage 40
- 2.2 Control Instruction 48
- Calls the specified job 52
- * (LABEL) 56
- ’ (COMMENT) 57
- Carries out no operation 59
- CWAIT END 61
- 2.3 Operating Instruction 64
- Sets Data 2 to Data 1 72
- (1) SET B000 0 81
- 0 is set in B000 81
- (2) SET P000 P001 81
- 2.3 Operating Instruction 100
- Instruction set: 101
- 6. (Element number) 109
- Variable No 120
- Add the following tag 121
- CNVRT PX000 PX001 BF 122
- Byte type 123
- SETE P000 (3) 2000 136
- Real-number 145
- SQRT R000 2 146
- SIN R000 60 148
- COS R000 60 150
- ATAN R000 60 152
- Variable No.Variable No 153
- P/LP/P[]/ 156
- INVMAT END 156
- 2. (Element number) 159
- SETFILE WEV#(1) (5) 3500 161
- D/LD/D[]/ 162
- 2.4 Move Instruction 164
- Job Type and Control Group 165
- Availability of Each Tag 166
- LEX [Array number] 167
- 16. +MOVJ/+MOVL/+MOVC/+MOVS 173
- MOVJ P000 VJ=50.00 174
- Corner radius 181
- 14. +MOVJ/+MOVL/+MOVC/+MOVS 184
- 13. +MOVJ/+MOVL/+MOVC/+MOVS 193
- 12. +MOVJ/+MOVL/+MOVC/+MOVS 202
- 2.4 Move Instruction 203
- 9. UNTIL/SRCH/NSRCH 210
- ×: Not available 212
- 1. Reference Point Number 217
- REFP1 REFP2 218
- Wall direction 221
- 2.5 Shift Instruction 222
- SFTOF END 227
- Input No 245
- 2.7 Arc Welding Instruction 248
- Arc generation mistake 251
- ARCON is processed again 251
- 2.7 Arc Welding Instruction 252
- Automatic sticking release 255
- For arc welding applications 261
- Starts weaving operation 265
- 1. RB1/RB2/RB3/RB4 266
- Reversed 269
- Welding” 270
- Ends weaving operation 271
- SUBSET STANDARD EXPANDED 273
- Available Available Available 273
- Function 273
- Construction 273
- 2.8 Handling Instruction 281
- Sensor No 283
- Time (s) 283
- 2.9 Spot Welding Instruction 285
- 2. MODE=Gun 1 operation mode 288
- ( ) LONG 291
- STROKE GUN#(1) LONG 293
- STRWAIT GUN#(1) LONG 293
Comments to this Manuals
© 2020, manymanuals.com. All rights reserved. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Obsługa robora