Yaskawa Z1000U User Manual Page 304
- Page / 378
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
u
S4: Bypass Operation
No.
(Addr.
Hex)
Name LCD Display Description Values Page
S4-01
(322B)
BP Auto Transfer on
Fault Enable
BP Fault Trnsfer
0: Disabled
1: Enabled
0: No transfer after fault
1: Transfer to bypass after fault
Default: 1
Range: 0, 1
–
S4-02
(322C)
Secondary PI User
Display
BP Enrgy Sav Lvl
Delta used to determine when to switch into Energy Save Bypass.
This allows for lower frequency output values to also trigger
Energy Save Bypass functionality.
Default: 0 Hz
Min.: 0
Max.: 20
–
S4-03
(322D)
BP Energy Save Bypass
Timer
BP Enrgy Sav TMR
Sets the time in seconds that the drive should run at the specified
speed before entering Energy Save Bypass mode.
Default: 60 s
Min.: 10
Max.: 60000
–
S4-04
(322E)
BP Energy Save Bypass
Speed Increase
BP Enrgy Sav Inc
Sets the value in Hz that the drive will increase the output
frequency above E1-04 before performing an Energy Save
transfer to bypass.
Default: 6 Hz
Min.: 0
Max.: 10
–
u
S5: HOA Keypad Parameters
No.
(Addr.
Hex)
Name LCD Display Description Values Page
S5-01
(322F)
HAND Frequency
Reference Selection
HAND Fref Source
0: Operator
1: Terminals
2: d1-16
3: S5-05
4: Set by b1-01
0: HOA keypad
1: Terminals
2: d1-16
3: S5-05
4: Determined by b1-01
Default: 0
Range: 0 to 4
–
S5-02
(3230)
HAND/AUTO During
Run Selection
HAND/AUTO
@Run
0: Disabled
1: Enabled
0: Disabled
1: Enabled Default: 1
Range: 0, 1
–
S5-03
(3231)
HAND Mode PI
Selection
HAND Mode PI Sel
0: Disabled
1: Enabled
0: Disabled
1: Enabled
Default: 1
Range: 0, 1
–
S5-04
(3232)
HAND Mode Behavior
Selection
HAND BehaviorSel
0: Legacy
1: Normal
2: Normal w/
Memory
0: Legacy operation mode
1: Normal operation mode
2: Normal with memory
Note: The drive will always be in AUTO mode at power
up with S5-04 = 1.
Default: 1
Range: 0 to 2
–
S5-05
(3233)
HAND Frequency
Reference 1
HAND Freq Ref 2
Sets the frequency reference used in HAND mode when S5-01 is
set to 2.
Default: 0.00
Hz
Min.: 0.00
Max.: E1-04
–
S5-07
(3235)
HAND Key Function
Selection (HOA
Keypad)
Oper HAND Key
0: Disabled
1: Enabled
Determines whether the HAND key on the HOA keypad will be
enabled for switching between HAND and AUTO.
0: Disabled
1: Enabled
Default: 1
Range: 0, 1
–
u
S6: Z1000U Protection
No.
(Addr.
Hex)
Name LCD Display Description Values Page
S6-01
(3236)
Emergency Override
Speed
E Override Speed
Sets the speed command used in Emergency Override mode when
S6-02 = 0.
Default: 0.00
Hz
Min.: 0.00
Max.: E1-04
–
S6-02
(3237)
Emergency Override
Reference Selection
E OverrideRefSel
0: Use S6-01 Ref
1: Use AUTO Ref
Selects the frequency reference source for the Emergency
Override function (H1-oo= AF or B0).
0: Use S6-01 Reference
1: Use AUTO Reference
Default: 0
Range: 0, 1
–
B.12 S: Special Application
304
YASKAWA ELECTRIC TOEP C710636 10B Z1000U HVAC MATRIX Drive User Manual
- Z1000U HVAC MATRIX Drive 1
- Table of Contents 3
- Preface & General Safety 11
- Applicable Documentation 12
- Terms and Abbreviations 12
- Trademarks 13
- WARNING 16
- Crush Hazard 16
- CAUTION 16
- Selection 17
- Carrier Frequency Derating 18
- Installation 18
- Settings 18
- General Handling 18
- Motor Application Precautions 19
- Specialized Motors 20
- Drive Label Warning Example 21
- Warranty Information 22
- Receiving 23
- 1.1 Section Safety 24
- 1.2 General Description 25
- Nameplate 27
- Z U 4 E A 28
- 1.5 Component Names 30
- IP20/NEMA Type 1 Enclosure 34
- Front Views 38
- Mechanical Installation 39
- 2.1 Section Safety 40
- 2.2 Mechanical Installation 42
- □0154A, 2□0192A, 2□0248 44
- HOA Keypad Remote Usage 45
- IP00 Enclosure Drives 49
- Electrical Installation 53
- 3.1 Section Safety 54
- 3.5 Terminal Cover 63
- Removing the HOA Keypad 66
- Reattaching the HOA Keypad 66
- Removing the Front Cover 66
- Front cover 67
- Reattaching the Front Cover 68
- 3.7 Top Protective Cover 69
- 3.8 Main Circuit Wiring 70
- Insulation Caps or Sleeves 71
- Main Circuit Protective Cover 71
- Three-Phase 200 V Class 72
- Ground Wiring 77
- R/L1 S/L2 T/L3 U/T1 V/T2 W/T3 81
- 3.9 Control Circuit Wiring 82
- Output Terminals 83
- Terminal Configuration 84
- 3.10 Control I/O Connections 88
- MEMOBUS/Modbus Termination 89
- 3.11 Connect to a PC 90
- 3.12 External Interlock 91
- 3.13 Wiring Checklist 92
- 4.1 Section Safety 94
- 4.2 Using the HOA Keypad 95
- Freq Ref 96
- ALARM (ALM) LED Displays 97
- Menu Structure for HOA Keypad 99
- 20 1 0/01/01 00:00 100
- Second per month 100
- YYYY/MM/DD HH:MM 100
- Start-Up Programming 101
- & Operation 101
- 20 10/01/01 00:00 102
- Entry accepted 102
- Entry Accepted 104
- Using the Setup Group 105
- Setup Group Parameters 106
- 4.4 Start-Up Flowcharts 107
- 4.5 Powering Up the Drive 111
- 4.6 Application Selection 112
- 0 to 10 V 116
- -10 to 10 V 116
- DC Injection brake time 118
- Max. output frequency (E1-04) 118
- E2-01: Motor Rated Current 122
- E2-11: Motor Rated Power 122
- 4.8 Auto-Tuning 131
- Before Auto-Tuning the Drive 132
- Auto-Tuning Operation Example 133
- Starting Auto-Tuning 135
- T1-02: Motor Rated Power 135
- <1> 136
- Checklist Before Operation 140
- Parameter Access Level: A1-01 141
- Copy Function 142
- A1-00: Language Selection 143
- A1-01: Access Level Selection 143
- A1-03: Initialize Parameters 144
- A1-06: Application Preset 145
- -100.0 to 100.0% 0.0% 149
- 0.00 to 100.00% 0.00% 153
- <1> 156
- Reference 157
- E1-03: V/f Pattern Selection 159
- H5-01: Drive Slave Address 165
- H5-07: RTS Control Selection 166
- L8-02: Overheat Alarm Level 168
- Output frequency 169
- U1: Operation Status Monitors 180
- U2: Fault Trace 180
- U3: Fault History 180
- U4: Maintenance Monitors 180
- U5: PID Monitors 181
- U6: Operation Status Monitors 181
- U9: Power Monitors 181
- This Page Intentionally Blank 182
- Troubleshooting 183
- 5.1 Section Safety 184
- Fire Hazard 185
- Fine-Tuning V/f Control 186
- Alarm and Error Displays 190
- Minor Faults and Alarms 191
- Operation Errors 191
- Auto-Tuning Errors 192
- 5.4 Fault Detection 193
- Cause Possible Solution 194
- 5.5 Alarm Detection 204
- Cause Possible Solutions 213
- Fault Reset Methods 219
- Common Problems 220
- Run Command 221
- Motor is Too Hot 222
- Oscillation or Hunting 225
- (Terminals DM+ and DM-) 227
- 6.1 Section Safety 230
- Peripheral Devices & 231
- 6.4 Option Installation 234
- Connecting a Surge Absorber 239
- Reducing Noise 239
- Long Motor Cables 240
- Appendix: A 241
- A.1 Power Ratings 242
- A.2 Drive Specifications 246
- A.2 Drive Specifications 247
- A.3 Drive Watt Loss Data 248
- A.4 Drive Derating Data 249
- Temperature Derating 250
- Altitude Derating 251
- Appendix: B 253
- OLV/PMOLV/PM 254
- A1: Initialization 255
- A2: User Parameters 255
- B.3 b: Application 256
- PID Offset 259
- PID Fdbk Offset 261
- B.4 C: Tuning 263
- C6: Carrier Frequency 264
- C7: Voltage Adjustment 264
- Adjustment 264
- Default: 0000 264
- B.5 d: References 265
- B.6 E: Motor Parameters 268
- B.7 F: Option Settings 271
- Parameter List 279
- TerminalA1Offset 285
- TerminalA2Offset 285
- H4: Analog Outputs 286
- B.9 L: Protection Function 289
- L3: Stall Prevention 290
- L4: Speed Detection 291
- L5: Fault Restart 292
- L6: Torque Detection 292
- L8: Drive Protection 293
- B.10 n: Special Adjustment 295
- B.12 S: Special Application 300
- S4: Bypass Operation 304
- S5: HOA Keypad Parameters 304
- S6: Z1000U Protection 304
- B.13 T: Motor Tuning 306
- T2: PM Motor Auto-Tuning 307
- B.14 U: Monitors 309
- Offset Frequency 316
- 000 000 000 kW 317
- 000 000 000 000 317
- Appendix: C 319
- C.1 BACnet Configuration 320
- Communications 321
- IG R+ R- S+ S 322
- Network Termination 323
- C.4 BACnet Setup Parameters 324
- Observing the Drive Operation 328
- Controlling the Drive 328
- C.6 Communications Timing 329
- C.7 BACnet Objects Supported 330
- Analog Input Objects 331
- Analog Output Objects 331
- Analog Value Objects 331
- Binary Input Objects 332
- Binary Output Objects 333
- Binary Value Objects 333
- Device Object 334
- Enter Command Types 335
- C.9 Communication Errors 336
- C.10 Self-Diagnostics 337
- Appendix: D 341
- D.1 Section Safety 342
- Standards Compliance 343
- D.2 European Standards 344
- D.3 UL and CSA Standards 347
- Three-Phase 400 V Class 349
- Drive Short Circuit Rating 355
- Appendix: E 357
- Drive Specifications 358
- Motor Specifications 358
- E.2 Basic Parameter Settings 359
- Monitor Outputs 360
- E.3 User Setting Table 361
- Numerics 367
- Revision History 376
Related products and manuals for Equipment Yaskawa Z1000U
Equipment Yaskawa JVOP-180 LCD User Manual
(58 pages)
(58 pages)
Equipment Yaskawa SI-EN3D User Manual
(68 pages)
(68 pages)
Equipment Yaskawa SI-ET3 User Manual
(49 pages)
(49 pages)
Equipment Yaskawa EtherNet/IP User Manual
(50 pages)
(50 pages)
Equipment Yaskawa PROFINET User Manual
(62 pages)
(62 pages)
Equipment Yaskawa BACnet MS/TP User Manual
(48 pages)
(48 pages)
© 2020, manymanuals.com. All rights reserved. | 1.171 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals