Yaskawa Z1000U User Manual Page 42
- Page / 378
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2.2 Mechanical Installation
This section outlines specifications, procedures, and the environment for proper mechanical installation of the drive.
u
Installation Environment
Install the drive in an environment matching the specifications in Table 2.1 to help prolong the optimum performance life of
the drive.
Table 2.1 Installation Environment
Environment Conditions
Installation Area Indoors
Ambient Temperature
IP00/Open Type enclosure: -10 °C to +50 °C (14 °F to 122 °F)
IP20/NEMA Type 1 enclosure: -10 °C to +40 °C (14 °F to 104 °F)
Drive reliability improves in environments without wide temperature fluctuations.
When using the drive in an enclosure panel, install a cooling fan or air conditioner in the area to ensure that the air
temperature inside the enclosure does not exceed the specified levels.
Do not allow ice to develop on the drive.
Humidity 95% RH or less and free of condensation
Storage Temperature -20 °C to +60 °C (-4 °F to +104 °F)
Surrounding Area
Install the drive in an area free from:
• oil mist and dust
• metal shavings, oil, water, or other foreign materials
• radioactive materials
• combustible materials (e.g., wood)
• harmful gases and liquids
• excessive vibration
• chlorides
• direct sunlight.
Altitude 1000 m (3281 ft.) or lower, up to 3000 m (9843 ft.) with derating
Vibration
10 to 20 Hz at 9.8 m/s
2
(32.15 ft/s
2
)
20 to 55 Hz at 5.9 m/s
2
(19.36 ft/s
2
) (Models 2o0028 to 2o0081 and 4o0011 to 4o0077)
2.0 m/s
2
(6.56 ft/s
2
) (Models 2o0104 to 2o0248 and 4o0096 to 4o0414)
Orientation Install the drive vertically to maintain maximum cooling effects.
NOTICE: Avoid placing drive peripheral devices, transformers, or other electronics near the drive as the noise created can lead to erroneous
operation. If such devices must be used in close proximity to the drive, take proper steps to shield the drive from noise.
NOTICE: Prevent foreign matter such as metal shavings and wire clippings from falling into the drive during installation. Failure to comply
could result in damage to the drive. Place a temporary cover over the top of the drive during installation. Remove the temporary cover before
drive start-up, as the cover will reduce ventilation and cause the drive to overheat.
u
Installation Orientation and Spacing
NOTICE: Install the drive upright as illustrated in Figure 2.1. Failure to comply may damage the drive due to improper cooling.
Figure 2.1 Correct Installation Orientation
NOTICE: Install the drive upright as specified in the manual. Failure to comply may damage the drive due to improper cooling.
n
Single Drive Installation
Figure 2.2 shows the installation distance required to maintain sufficient space for airflow and wiring.
2.2 Mechanical Installation
42
YASKAWA ELECTRIC TOEP C710636 10B Z1000U HVAC MATRIX Drive User Manual
- Z1000U HVAC MATRIX Drive 1
- Table of Contents 3
- Preface & General Safety 11
- Applicable Documentation 12
- Terms and Abbreviations 12
- Trademarks 13
- WARNING 16
- Crush Hazard 16
- CAUTION 16
- Selection 17
- Carrier Frequency Derating 18
- Installation 18
- Settings 18
- General Handling 18
- Motor Application Precautions 19
- Specialized Motors 20
- Drive Label Warning Example 21
- Warranty Information 22
- Receiving 23
- 1.1 Section Safety 24
- 1.2 General Description 25
- Nameplate 27
- Z U 4 E A 28
- 1.5 Component Names 30
- IP20/NEMA Type 1 Enclosure 34
- Front Views 38
- Mechanical Installation 39
- 2.1 Section Safety 40
- 2.2 Mechanical Installation 42
- □0154A, 2□0192A, 2□0248 44
- HOA Keypad Remote Usage 45
- IP00 Enclosure Drives 49
- Electrical Installation 53
- 3.1 Section Safety 54
- 3.5 Terminal Cover 63
- Removing the HOA Keypad 66
- Reattaching the HOA Keypad 66
- Removing the Front Cover 66
- Front cover 67
- Reattaching the Front Cover 68
- 3.7 Top Protective Cover 69
- 3.8 Main Circuit Wiring 70
- Insulation Caps or Sleeves 71
- Main Circuit Protective Cover 71
- Three-Phase 200 V Class 72
- Ground Wiring 77
- R/L1 S/L2 T/L3 U/T1 V/T2 W/T3 81
- 3.9 Control Circuit Wiring 82
- Output Terminals 83
- Terminal Configuration 84
- 3.10 Control I/O Connections 88
- MEMOBUS/Modbus Termination 89
- 3.11 Connect to a PC 90
- 3.12 External Interlock 91
- 3.13 Wiring Checklist 92
- 4.1 Section Safety 94
- 4.2 Using the HOA Keypad 95
- Freq Ref 96
- ALARM (ALM) LED Displays 97
- Menu Structure for HOA Keypad 99
- 20 1 0/01/01 00:00 100
- Second per month 100
- YYYY/MM/DD HH:MM 100
- Start-Up Programming 101
- & Operation 101
- 20 10/01/01 00:00 102
- Entry accepted 102
- Entry Accepted 104
- Using the Setup Group 105
- Setup Group Parameters 106
- 4.4 Start-Up Flowcharts 107
- 4.5 Powering Up the Drive 111
- 4.6 Application Selection 112
- 0 to 10 V 116
- -10 to 10 V 116
- DC Injection brake time 118
- Max. output frequency (E1-04) 118
- E2-01: Motor Rated Current 122
- E2-11: Motor Rated Power 122
- 4.8 Auto-Tuning 131
- Before Auto-Tuning the Drive 132
- Auto-Tuning Operation Example 133
- Starting Auto-Tuning 135
- T1-02: Motor Rated Power 135
- <1> 136
- Checklist Before Operation 140
- Parameter Access Level: A1-01 141
- Copy Function 142
- A1-00: Language Selection 143
- A1-01: Access Level Selection 143
- A1-03: Initialize Parameters 144
- A1-06: Application Preset 145
- -100.0 to 100.0% 0.0% 149
- 0.00 to 100.00% 0.00% 153
- <1> 156
- Reference 157
- E1-03: V/f Pattern Selection 159
- H5-01: Drive Slave Address 165
- H5-07: RTS Control Selection 166
- L8-02: Overheat Alarm Level 168
- Output frequency 169
- U1: Operation Status Monitors 180
- U2: Fault Trace 180
- U3: Fault History 180
- U4: Maintenance Monitors 180
- U5: PID Monitors 181
- U6: Operation Status Monitors 181
- U9: Power Monitors 181
- This Page Intentionally Blank 182
- Troubleshooting 183
- 5.1 Section Safety 184
- Fire Hazard 185
- Fine-Tuning V/f Control 186
- Alarm and Error Displays 190
- Minor Faults and Alarms 191
- Operation Errors 191
- Auto-Tuning Errors 192
- 5.4 Fault Detection 193
- Cause Possible Solution 194
- 5.5 Alarm Detection 204
- Cause Possible Solutions 213
- Fault Reset Methods 219
- Common Problems 220
- Run Command 221
- Motor is Too Hot 222
- Oscillation or Hunting 225
- (Terminals DM+ and DM-) 227
- 6.1 Section Safety 230
- Peripheral Devices & 231
- 6.4 Option Installation 234
- Connecting a Surge Absorber 239
- Reducing Noise 239
- Long Motor Cables 240
- Appendix: A 241
- A.1 Power Ratings 242
- A.2 Drive Specifications 246
- A.2 Drive Specifications 247
- A.3 Drive Watt Loss Data 248
- A.4 Drive Derating Data 249
- Temperature Derating 250
- Altitude Derating 251
- Appendix: B 253
- OLV/PMOLV/PM 254
- A1: Initialization 255
- A2: User Parameters 255
- B.3 b: Application 256
- PID Offset 259
- PID Fdbk Offset 261
- B.4 C: Tuning 263
- C6: Carrier Frequency 264
- C7: Voltage Adjustment 264
- Adjustment 264
- Default: 0000 264
- B.5 d: References 265
- B.6 E: Motor Parameters 268
- B.7 F: Option Settings 271
- Parameter List 279
- TerminalA1Offset 285
- TerminalA2Offset 285
- H4: Analog Outputs 286
- B.9 L: Protection Function 289
- L3: Stall Prevention 290
- L4: Speed Detection 291
- L5: Fault Restart 292
- L6: Torque Detection 292
- L8: Drive Protection 293
- B.10 n: Special Adjustment 295
- B.12 S: Special Application 300
- S4: Bypass Operation 304
- S5: HOA Keypad Parameters 304
- S6: Z1000U Protection 304
- B.13 T: Motor Tuning 306
- T2: PM Motor Auto-Tuning 307
- B.14 U: Monitors 309
- Offset Frequency 316
- 000 000 000 kW 317
- 000 000 000 000 317
- Appendix: C 319
- C.1 BACnet Configuration 320
- Communications 321
- IG R+ R- S+ S 322
- Network Termination 323
- C.4 BACnet Setup Parameters 324
- Observing the Drive Operation 328
- Controlling the Drive 328
- C.6 Communications Timing 329
- C.7 BACnet Objects Supported 330
- Analog Input Objects 331
- Analog Output Objects 331
- Analog Value Objects 331
- Binary Input Objects 332
- Binary Output Objects 333
- Binary Value Objects 333
- Device Object 334
- Enter Command Types 335
- C.9 Communication Errors 336
- C.10 Self-Diagnostics 337
- Appendix: D 341
- D.1 Section Safety 342
- Standards Compliance 343
- D.2 European Standards 344
- D.3 UL and CSA Standards 347
- Three-Phase 400 V Class 349
- Drive Short Circuit Rating 355
- Appendix: E 357
- Drive Specifications 358
- Motor Specifications 358
- E.2 Basic Parameter Settings 359
- Monitor Outputs 360
- E.3 User Setting Table 361
- Numerics 367
- Revision History 376
Related products and manuals for Equipment Yaskawa Z1000U
Equipment Yaskawa JVOP-180 LCD User Manual
(58 pages)
(58 pages)
Equipment Yaskawa SI-EN3D User Manual
(68 pages)
(68 pages)
Equipment Yaskawa SI-ET3 User Manual
(49 pages)
(49 pages)
Equipment Yaskawa EtherNet/IP User Manual
(50 pages)
(50 pages)
Equipment Yaskawa PROFINET User Manual
(62 pages)
(62 pages)
Equipment Yaskawa BACnet MS/TP User Manual
(48 pages)
(48 pages)
© 2020, manymanuals.com. All rights reserved. | 0.706 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals