Yaskawa F7 Drive User Manual User Manual download pdf (Page 97)

Start-Up 4 - 12

 Quick Setting Parameters

The following Drive parameters located in the Quick Setting menu need to be set according to the application. Refer to

Chapter 5 Basic Programming section for more details on each parameter.

Note: Not all parameters are available for all Control Methods. See Control Method column.

Parameter

No.

Parameter Name

Digital Operator Display

Description

Setting

Range

Factory

Setting

Control Method

V/F

OLV FV

A1-02

Control Method Selection

Control Method

Selects the Control Method of the Drive.

0: V/F control without PG

1: V/F control with PG

2: Open Loop Vector

3: Flux Vector (Closed Loop Vector)

0 to 3 0 Q Q Q Q

b1-01

Frequency Reference

Selection

Reference Source

Selects the frequency reference input source.

0: Operator - Digital preset speed U1-01 or d1-01 to d1-17.

1: Terminals - Analog Input Terminal A1 (Terminal A2 sums

together with terminal A1 when H3-09=0)

2: Serial Com - Modbus RS-422/485 terminals R+, R-, S+ and S-

3: Option PCB - Option board connected on 2CN

4: Pulse Input

0 to 4 1 Q Q Q Q

b1-02

Run Command Selection

Run Source

Selects the run command input source.

0: Operator - RUN and STOP keys on Digital Operator

1: Terminals - Contact closure on terminals S1 or S2

2: Serial Com - Modbus RS-422/485 terminals R+, R-, S+ and S-

3: Option PCB - Option board connected on 2CN

0 to 3 1 Q Q Q Q

b1-03

Stopping Method Selection

Stopping Method

Selects the stopping method when the run command is removed.

0: Ramp to Stop

1: Coast to Stop

2: DC Injection to Stop

3: Coast with Timer (A new run command is ignored if input

before the timer expires.)

0 to 3 0 Q Q Q Q

C1-01



Acceleration Time 1

Accel Time 1

Sets the time to accelerate from zero to maximum frequency

(E1-04).

0.0

6000.0

10.0sec

QQ Q Q

C1-02



Deceleration Time 1

Decel Time 1

Sets the time to decelerate from maximum frequency to zero

(E1-04).

QQ Q Q

C6-02

Carrier Frequency Selection

CarrierFreq Sel

Selects the number of pulses per second of the output voltage

waveform. Setting range determined by C6-01 setting.

0: Low noise

1: Fc = 2.0 kHz

2: Fc = 5.0 kHz

3: Fc = 8.0 kHz

4: Fc = 10.0 kHz

5: Fc = 12.5 kHz

6: Fc = 15.0 kHz

F: Program (Determined by the settings of C6-03 thru C6-05)

Va ri es

kVA

Va ri es

kVA

QQ Q Q

d1-01



Frequency Reference 1

Reference 1

Setting units are affected by o1-03.

0.00

E1-04

Va lu e

0.00Hz Q Q Q Q

d1-02



Frequency Reference 2

Reference 2

Frequency reference when multi-function input “Multi-step speed

reference 1” is ON. Setting units are affected by o1-03.

0.00Hz Q Q Q Q

d1-03



Frequency Reference 3

Reference 3

Frequency reference when multi-function input “Multi-step speed

reference 2” is ON. Setting units are affected by o1-03.

0.00Hz Q Q Q Q

d1-04



Frequency Reference 4

Reference 4

Frequency reference when multi-function input “Multi-step speed

reference 1,2” is ON. Setting units are affected by o1-03.

0.00Hz Q Q Q Q

d1-17



Jog Frequency Reference

Jog Reference

Frequency reference when:

“Jog Frequency Reference”, “Forward Jog”, or “Reverse Jog” is

selected via multi-function input terminals or JOG key is pressed

on the operator keypad. Jog reference has priority over frequency

reference 1 to 4. Setting units are affected by o1-03.

6.00Hz Q Q Q Q

Denotes that parameter can be changed when the Drive is running.

1 2 ... 92 93 94 95 96 97 98 99 100 101 102 ... 254 255

Yaskawa F7 Drive User Manual User Manual Page 97

Comments to this Manuals

Yaskawa F7 Drive User Manual User Manual Page 97

Comments to this Manuals

Related products and manuals for Equipment Yaskawa F7 Drive User Manual