YASKAWA VS-626M5 Instruction Manual Page 37
- Page / 268
- Table of contents
- BOOKMARKS
- SENTROL 2 1
- For Safe Maintenance 6
- War ning 10
- CUSTOM MACRO 18
- 2. ALARM MESSAGE 19
- 2.2 ALARM LIST 19
- Only L line On 21
- Only M line 21
- Only L line 29
- 2. 3 THERMAL ALARM 35
- * 37
- * 37
- ’ key 39
- Deceleration 44
- Reference Position 44
- 5. Abnormalities on Screen 47
- 5.3 Stripes on the Screen 48
- 6. Power ON Malfunction 49
- 7. Communication Troubles 50
- Chapter 2 Servo 51
- □ RPR ERROR 52
- □ EXCESS ERROR (STOP) 53
- □ EXCESS ERROR (MOVING) 54
- □ DRIFT OVER 55
- □ READY OFF ERROR 56
- □ READY ON ERROR 57
- □ ENCODER DISCONNECT 57
- □ EXCESS ERROR (SERVO OFF) 58
- □ PULSE COUNT MISS (ENC) 58
- □ AUTO GAIN OVER 59
- □ SERVO ALARM 59
- Chapter 3 Spindle 60
- Chapter 3 SPINDLE 61
- 2.2 Fuse 66
- 2.3 Validation of DC Voltage 66
- 4. How to Adjust Screen 68
- 5. How to Adjust Servo 69
- 5.2 Zero Setting 70
- (Decelerating) 72
- (Accelerating) 72
- 5.5 Load Torque Check 73
- NEXT SEL 75
- 1. System Configuration 78
- 2. Configuration of Main Unit 79
- 3. Connector Layouts 80
- Sentrol2 81
- 3.2 Connectors of DKU 82
- ItemNo.ofPrintedBoard 83
- EPS4 board NO.3 84
- EPS3 board NO.3 86
- Item No. of Printed Board 87
- 3.5 Connectors of DIO3 Board 88
- 3.5 Connectors of DIO3 BOARD 90
- 4. Installation 91
- 4.7 Noise Countermeasure 92
- 2. PLC Diagnosis 100
- 2.1 PLC Signal List 1 100
- Chapter 6 Self-diagnosis 101
- DESCRIPTIONSIGNALADDRESS BIT 110
- BIT SIGNAL 125
- DESCRIPTION 125
- 2.2 PLC Signal List 2 130
- DATA NUM 140
- TRIGGER 140
- DISP POS 140
- Setting 142
- Completed 142
- INITIAL 143
- PARAMETER 143
- 4. General Diagnosis 147
- Chapter 7 Parameter 152
- 1.1 Parameter Setting Method 154
- Chapter 7 Parameter 157
- rate 168
- Ts/2 Ts/2 170
- Velocity 170
- Time(msec) 170
- POSITION ERROR 178
- HIGH SPEED POSITIONING 178
- NORMAL POSITIONING 178
- 1 0 1024PPR 195
- 1 1 2048PPR 195
- Assigned coordinate system 235
- Chapter 8 Ordinary Repair 247
- Appendix 249
- 2. DIO3 Board I/O Signal List 250
- 3. RIO1 Board I/O Signal List 251
- 8. FDD Connection 253
- 10. LAN INTERFACE 254
- UNIT and DKU 254
- 12. AC SERVO Connection 255
- 12.1 YASKAWA SIGMA 255
- 12.3 HYOSUNG/YASKAWA 257
- APPENDIX 258
- 12. AC SERVO CONNECTION 259
- 12.5 MITSUBISHI MR-J2 259
- MAIN UNIT 260
- 12.7 AC220V POWER CONNECTION 261
- 13. SPINDLE UNIT CONNECTION 263
- 13.3 MITSUBISI MDS-A-SPA 263
- CABLE CNS1 265
- 20PIN SHIELD CABLE 265
- CONNECT TO THE EARTH PLATE 265
- OF THE CABINET 265
- 14. DNC FUNCTION 267
© 2020, manymanuals.com. All rights reserved. | 0.502 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals