YASKAWA Varispeed-606PC3 Instruction Manual Page 160
- Page / 256
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
7. Programming Features
159
Factory Settings
Note: Terminals S5 through S7 can be used only from DeviceNet communica-
tions. There are no corresponding external terminals.
Terminal Functions for 3-wire Sequence Selection
When 0 is set for terminal S3 (n052), terminal S1 is the RUN command,
terminal S2 is the STOP command, and terminal S3 is the FWD/REV
RUN command.
To select the 3-wire sequence, set terminal S3 (n052)
to 0.
Failure to observe this warning may result in injury.
No. Terminal Factory Setting Function
n050 S1 1 FORWARD RUN command (2-
wire sequence)
n051 S2 2 REVERSE RUN command (2-
wire sequence)
n052 S3 3 External fault
n053 S4 5 Fault reset
n054 S5
(See note.)
6 Multi-step speed reference 1
n055 S6
(See note.)
7 Multi-step speed reference 2
n056 S7
(See note.)
10 JOG command
RUN command
(Run when closed)
STOP command
(Stop when open)
FWD/REV run selection
FWD run when open
REV run when closed
RUN SW
(NO contact)
STOP SW
(NC contact)
Varispeed V7
WARNING
- INSTRUCTION MANUAL 1
- General Precautions 2
- PRECAUTIONS FOR CE MARKINGS 4
- RECEIVING THE PRODUCT 5
- MOUNTING 5
- OPERATION 8
- MAINTENANCE AND INSPECTION 10
- (Ref. page) 11
- WARNING LABEL 12
- Warning Label 13
- Japanese 13
- WARRANTY INFORMATION 14
- RESTRICTIONS 15
- CONTENTS 16
- Revision History 19
- 1. Receiving the Product 20
- Checking the Nameplate 21
- 2. Identifying the Parts 22
- 3. Mounting 25
- Mounting Dimensions 26
- IMPORTANT 27
- 4. Wiring 29
- Wiring Instructions 30
- Wiring the Main Circuits 37
- Wiring the Control Circuits 39
- Black Blue White Red 40
- Wiring Inspection 41
- 5. Operating the Inverter 42
- Test Run 43
- Operation Check Points 44
- JVOP-140 Digital Operator 45
- Selecting the Monitor 49
- Monitoring 50
- Input terminal status 52
- Output terminal status 52
- 4-digit number 53
- : Order of fault (1 to 4) 53
- : Fault description 53
- Simple Data Setting 54
- or 55
- or key 55
- 6. Operating with DeviceNet 56
- Communications 56
- Rotary Switches 57
- Baud Rate Setting Switch (S1) 57
- Initial Settings 58
- I/O Message Communications 60
- Basic I/O Instances 60
- MEMOBUS I/O Instances 65
- Function Codes 83
- Function Status 88
- Header MAC ID Service 95
- • Object Contents 100
- (400 V) 115
- Error Code Tables 117
- MEMOBUS Register Tables 120
- Constant Data 126
- 7. Programming Features 128
- Using V/f Control Mode 130
- Motor Specification: 60 Hz 131
- Motor Specification: 50 Hz 131
- (Factory setting) 131
- Operation 132
- Using Vector Control Mode 133
- Motor Constant Calculation 134
- [Motor Specification: 60 Hz] 135
- [Motor Specification: 50 Hz] 135
- Switching LOCAL/REMOTE Mode 136
- Selecting RUN/STOP Commands 137
- REMOTE Mode 138
- LOCAL Mode 138
- Reverse Run Prohibit (n006) 140
- Multi-step Speed Selection 140
- Operating at Low Speed 142
- 0 V 10 V 143
- Acceleration 146
- Deceleration 146
- Motor current 147
- Multi-function output signal 147
- (overtorque detection signal) 147
- Terminal MA, P1, or P2 147
- Frequency Detection 2 149
- SPEED SEARCH Command 150
- Command Input 151
- Deceleration to a Stop 156
- Coast to a Stop 157
- Using Input Signals 158
- Varispeed V7 160
- (Setting: 18) 163
- Analog Input Level 164
- Output frequency 169
- Motor Protection 173
- Voltage fluctuation 178
- Output voltage 178
- Motor Code 179
- Using PID Control Mode 180
- (n130, n131, n132) 182
- PID Offset Adjustment (n133) 183
- PID Output Gain (n163) 183
- PID Feedback Gain (n129) 183
- PID Limit 184
- Prohibition of PID Output 184
- PID Control Block Diagram 185
- Inverter 186
- Constant Copy Function 187
- READ Function 189
- COPY Function 190
- VERIFY Function 191
- Inverter Capacity Display 193
- Software No. Display 195
- Display List 195
- Function Is Valid 197
- Loss (n064) 199
- Undertorque Detection 201
- Periodic Inspection 204
- Part Replacement 205
- Airflow direction 206
- 9. Fault Diagnosis 208
- Alarm Displays and Meaning 209
- Flashing 211
- Indicators 219
- Troubleshooting 221
- 10. Specifications 224
- conform to CE requirements 232
- Use sequencer to 233
- Transistor 235
- Surge Suppressors 241
- Constants List 243
- −100% to 249
- • 200 V Class Single-phase 253
- • 400 V Class 3-phase 253
Related products and manuals for Power adapters & inverters YASKAWA Varispeed-606PC3
(138 pages)
(122 pages)© 2020, manymanuals.com. All rights reserved. | 0.622 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals