YASKAWA Varispeed-606PC3 Instruction Manual Page 40
- Page / 256
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4. Wiring
39
Wiring the DeviceNet Communications Cable
Use the following procedure to wire the DeviceNet communications
cable to the terminal block (CN6).
1. Use a thin slotted screwdriver to loosen the terminal screws.
2. Insert the power supply wires into the terminal block from below.
3. Tighten the terminal screws securely so that the power supply wires
will not come out of the terminal block.
Terminal Block (CN6) Wiring Example
* 1. Always use thin DeviceNet cable that meets DeviceNet cable specifica-
tions.
* 2. Match the color of the power supply wires with the color of the terminal
block terminals when wiring.
Terminal
Color
Name Wire Color Description
Black V− Black Communications pow-
er supply GND
Blue CAN_L Blue Communications data
low
Colorless Shield (Shield) Shield wire
White CAN_H White Communications data
high
Red V+ Red Communications pow-
er supply +24 VDC
Strip about 5.5 mm (1/4 inch)
of the wire sheath.
Power supply wire
Terminal block
Black Blue White Red
Black Blue White Red
- INSTRUCTION MANUAL 1
- General Precautions 2
- PRECAUTIONS FOR CE MARKINGS 4
- RECEIVING THE PRODUCT 5
- MOUNTING 5
- OPERATION 8
- MAINTENANCE AND INSPECTION 10
- (Ref. page) 11
- WARNING LABEL 12
- Warning Label 13
- Japanese 13
- WARRANTY INFORMATION 14
- RESTRICTIONS 15
- CONTENTS 16
- Revision History 19
- 1. Receiving the Product 20
- Checking the Nameplate 21
- 2. Identifying the Parts 22
- 3. Mounting 25
- Mounting Dimensions 26
- IMPORTANT 27
- 4. Wiring 29
- Wiring Instructions 30
- Wiring the Main Circuits 37
- Wiring the Control Circuits 39
- Black Blue White Red 40
- Wiring Inspection 41
- 5. Operating the Inverter 42
- Test Run 43
- Operation Check Points 44
- JVOP-140 Digital Operator 45
- Selecting the Monitor 49
- Monitoring 50
- Input terminal status 52
- Output terminal status 52
- 4-digit number 53
- : Order of fault (1 to 4) 53
- : Fault description 53
- Simple Data Setting 54
- or 55
- or key 55
- 6. Operating with DeviceNet 56
- Communications 56
- Rotary Switches 57
- Baud Rate Setting Switch (S1) 57
- Initial Settings 58
- I/O Message Communications 60
- Basic I/O Instances 60
- MEMOBUS I/O Instances 65
- Function Codes 83
- Function Status 88
- Header MAC ID Service 95
- • Object Contents 100
- (400 V) 115
- Error Code Tables 117
- MEMOBUS Register Tables 120
- Constant Data 126
- 7. Programming Features 128
- Using V/f Control Mode 130
- Motor Specification: 60 Hz 131
- Motor Specification: 50 Hz 131
- (Factory setting) 131
- Operation 132
- Using Vector Control Mode 133
- Motor Constant Calculation 134
- [Motor Specification: 60 Hz] 135
- [Motor Specification: 50 Hz] 135
- Switching LOCAL/REMOTE Mode 136
- Selecting RUN/STOP Commands 137
- REMOTE Mode 138
- LOCAL Mode 138
- Reverse Run Prohibit (n006) 140
- Multi-step Speed Selection 140
- Operating at Low Speed 142
- 0 V 10 V 143
- Acceleration 146
- Deceleration 146
- Motor current 147
- Multi-function output signal 147
- (overtorque detection signal) 147
- Terminal MA, P1, or P2 147
- Frequency Detection 2 149
- SPEED SEARCH Command 150
- Command Input 151
- Deceleration to a Stop 156
- Coast to a Stop 157
- Using Input Signals 158
- Varispeed V7 160
- (Setting: 18) 163
- Analog Input Level 164
- Output frequency 169
- Motor Protection 173
- Voltage fluctuation 178
- Output voltage 178
- Motor Code 179
- Using PID Control Mode 180
- (n130, n131, n132) 182
- PID Offset Adjustment (n133) 183
- PID Output Gain (n163) 183
- PID Feedback Gain (n129) 183
- PID Limit 184
- Prohibition of PID Output 184
- PID Control Block Diagram 185
- Inverter 186
- Constant Copy Function 187
- READ Function 189
- COPY Function 190
- VERIFY Function 191
- Inverter Capacity Display 193
- Software No. Display 195
- Display List 195
- Function Is Valid 197
- Loss (n064) 199
- Undertorque Detection 201
- Periodic Inspection 204
- Part Replacement 205
- Airflow direction 206
- 9. Fault Diagnosis 208
- Alarm Displays and Meaning 209
- Flashing 211
- Indicators 219
- Troubleshooting 221
- 10. Specifications 224
- conform to CE requirements 232
- Use sequencer to 233
- Transistor 235
- Surge Suppressors 241
- Constants List 243
- −100% to 249
- • 200 V Class Single-phase 253
- • 400 V Class 3-phase 253
Related products and manuals for Power adapters & inverters YASKAWA Varispeed-606PC3
(138 pages)
(122 pages)© 2020, manymanuals.com. All rights reserved. | 1.760 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals